Tripp Lite SMX2200XLRT2U owner manual Other UPS Features Rear Panel

Page 9

Basic Operation continued

Other UPS Features (Rear Panel)

IEC320-

C13/230V

AC Receptacles: Your UPS features IEC320-C13 outlets. These output receptacles provide your connected equipment with AC line power during normal operation and battery power during blackouts and brownouts. The UPS protects equipment connected to these receptacles against damaging surges and line noise. If you have a serial or USB connection to your UPS, you can remote- ly reboot connected equipment by turning individually controllable receptacles OFF and ON using Tripp Lite's PowerAlert Software. Three receptacles, labeled LOAD 1, LOAD 2 and LOAD 3, are individually controllable and may be remotely switched OFF and ON using PowerAlert Software without interrupting power to equipment connected to other outlets. Outlets labeled UNSWITCHED may not be remotely turned off. Unswitched outlets can only be turned off by turning off all output receptacles. See software instructions for details.

Communications Ports (USB or RS-232): These ports connect your UPS to any workstation or server. Use with Tripp Lite’s PowerAlert Software and included cables to enable your computer to automatically save open files and shut down equipment during a blackout. Also use PowerAlert Software to mon- itor a wide variety of AC line power and UPS operating conditions. Consult your PowerAlert Software manual or contact Tripp Lite Customer Support for more information. See “USB and RS-232 Serial Communications” in the “Optional Installation” section for installation instructions.

EPO (Emergency Power Off) Port: Your UPS features a EPO port that may be used to connect the UPS to a contact closure switch to enable emergency inverter shutdown. See Optional Installation.

NO EXTERNAL

BATTERIES

EXTERNAL

BATTERIES

Voltage DIP Switches: These switches enable the UPS to be set to match actual input voltage. If the Voltage DIP Switches are set above or below input voltage, the UPS will treat the input as a continuous overvoltage or undervolt- age condition, and will automatically adjust input voltage to match the Voltage DIP Switch setting. This will cause constant, unnecessary wear on the UPS.

Note: The Voltage DIP Switches must be set with the UPS turned OFF and disconnected from utility power. If the switches are set while the UPS is connected to utility power, the setting will not take effect.

9

Image 9
Contents Intelligent, Line-Interactive UPS System SmartProBattery Warnings Important Safety InstructionsUPS Location Warnings UPS Connection WarningsPost Telecom Mounting Mounting RackMounting Tower Turn the UPS on USB and RS-232 Serial Communications Buttons Front Panel Indicator Lights Front Panel Other UPS Features Rear Panel Basic Operation Storage ServiceReplace Front Panel ProcedureSistema de UPS, Inteligentes y Interactivos en Línea Manual del propietarioAdvertencias sobre la ubicación del UPS Instrucciones de seguridad importantesAdvertencias sobre la conexión del UPS Advertencias sobre la conexión de equiposMontaje Bastidor Montaje de 4 postesMontaje de 2 postes Telecomunicaciones Montaje En torre Encienda el UPS Con el no-break desconectado de laComunicaciones USB y serie RS-232 Todos los modelos Conexión de puerto EPO Todos los modelosConexión de batería externa Botones Panel frontal Luces indicadoras Panel frontal Operación básica continúaOtras funciones del UPS Panel posterior Operación básica continúa Almacenamiento ServicioCumplimiento de las normas de los números de identificación ProcedimientoSystémes UPS intelligent, en attente active Manuel du propriétaireDirectives de sécurité importantes Mises en garde Emplacement de lUPSMises en garde Connexions de lUPS Mises en garde Connexion déquipementMontage Bâti Bâti à quatre montantsMontage sur 2 montants Télécom Montage Tour Londuleur UPS étant déconnecté du Connexion de batterie externe Connexion au port EPO tous les modèlesBoutons Panneau avant Voyants indicateurs Panneau avant Fonctionnement de base, suiteAutres caractéristiques de lUPS panneau arrière Fonctionnement de base, suite Entreposage ServiceReplacer le panneau avant ProcédureIntelligentes USV-System mit aktivem Standby-Modus BesitzerhandbuchWarnhinweis zum Aufstellungsort der USV Wichtige SicherheitsinstruktionenWarnhinweise zum Anschluss der USV Warnung zum Anschluss von GerätenMontage mit vier Ständern Montage BaugruppenrahmenMontage Turm Schalten Sie die USV ein Schließen Sie Ihr Gerät an die USV anUSB und RS-232 serielle Kommunikationsanschlüsse Taste „ON/OFF/STANDBY EIN/AUS/STABNDBY Tasten Vorderes BedienfeldAnzeigeleuchten Vorderes Bedienfeld Grundbetrieb FortsetzungSonstige USV-Funktionsmerkmale Rückseite Einstellung der Lagerung Vorgehensweise AkkuaustauschÐóêîâîäñòâî ïîëüçîâàòåëÿ Ñîõðàíèòå ÝÒÈ Èíñòðóêöèè Âàæíûå èíñòðóêöèè ïî òåõíèêå áåçîïàñíîñòèÎïîðíûé ìîíòàæ Ìîíòàæ ÑòîéêàÌîíòàæ Áàøíÿ, ïèëîí ÓÏÑ Áûñòðàÿ óñòàíîâêàÏîðòû ïîñëåäîâàòåëüíîé ñâÿçè 1USB è RS-232 âñå ìîäåëè Äîïîëíèòåëüíûé ìîíòàæÊíîïêè Ïåðåäíÿÿ ïàíåëü Îñíîâíîé ðåæèì ðàáîòûÈíäèêàòîðíûå ëàìïî÷êè Ïåðåäíÿÿ ïàíåëü Îñíîâíîé ðåæèì ðàáîòû, ïðîäîëæåíèåÄðóãèå âîçìîæíîñòè ÓÏÑ Çàäíÿÿ ïàíåëü Îñíîâíîé ðåæèì ðàáîòû, ïðîäîëæåíèå Õðàíåíèå Õðàíåíèå è îáñëóæèâàíèåÑíèìèòå ïåðåäíþþ ïàíåëü Çàìåíà àêêóìóëÿòîðà