Delta Electronics VFD-XXXE quick start Summary of Parameter Settings, Group 0 User Parameters

Page 10

Terminal	Terminal Function		Factory Settings (NPN mode)
Symbol	Terminal Function			ON: Connect to DCM
Symbol				ON: Connect to DCM
			Maximum 48VDC, 50mA
			Refer to Pr.03.01 for programming
			MO1-DCM		Max: 48Vdc
			MO1-DCM		50mA
					50mA
MO1	Multi-function Output 1			Mo1
	Multi-function Output 1
	(Photocoupler)
	(Photocoupler)
				MCM
				internal circuit
MCM	Multi-function output common		Common for Multi-function Outputs
+10V	Potentiometer power supply		+10VDC 3mA
	Analog voltage Input		Impedance:	47kΩ
	+10V	AVI circuit	Impedance:	47kΩ
		AVI circuit	Resolution:	10 bits
			Resolution:	10 bits
			Range:	0 ~ 10VDC =
AVI	AVI			0 ~ Max. Output Frequency
				(Pr.01.00)
			Selection:	Pr.02.00, Pr.02.09, Pr.10.00
	ACM	internal circuit	Set-up:	Pr.04.11 ~ Pr.04.14
		internal circuit
ACM	Analog control signal		Common for AVI, ACI, AFM
ACM	(common)		Common for AVI, ACI, AFM
	(common)
	Analog current Input		Impedance:	250Ω
	ACI circuit		Impedance:	250Ω
	ACI		Resolution:	10 bits
ACI			Range:	4 ~ 20mA =
ACI				0 ~ Max. Output Frequency
				(Pr.01.00)
			Selection:	Pr.02.00, Pr.02.09, Pr.10.00
	ACM internal circuit		Set-up:	Pr.04.15 ~ Pr.04.18, 04.19~04.23
	ACM internal circuit
	Analog output meter		0 to 10V, 2mA
	ACM circuit		0 to 10V, 2mA
	ACM circuit
		AFM	Impedance:	20kΩ
			Impedance:	20kΩ
AFM		0~10V	Output current	2mA max
AFM		0~10V	Resolution:	8 bits
		potentiometer	Resolution:	8 bits
		Max. 2mA	Range:	0 ~ 10VDC
			Function:	Pr.03.03 to Pr.03.04
	internal circuit ACM
NOTE: Control signal wiring size: 18 AWG (0.75 mm2) with shielded wire.
Summary of Parameter Settings
: The parameter can be set during operation.					Factory
Pr.	Explanation		Settings		Factory	NOTE
Pr.	Explanation		Settings		Setting	NOTE
		Group 0 User Parameters			Setting
		Group 0 User Parameters
00.00	Identity Code of the Read-only				##
	AC motor drive

English- 10

Image 10

Contents Preface Specifications Voltage Class 115V ClassGeneral Specifications Basic Wiring Diagram SL2 VT2 TL3 WT3+/B1 Signal Description PNP mode without external powerDescription of the Digital Keypad KPE-LE02 Optional Operation Steps of the Digital Keypad To shift dataTerminal Symbol Power Terminals and Control TerminalsFrame Power Terminals Torque Wire Wire Type Terminal ExplanationsControl Terminals Explanations Specification for the Control TerminalsFrame Control Terminals Torque Summary of Parameter Settings Group 0 User ParametersNot for VFD*E*C models Explanation Settings FactoryModels VFD*E*C modelsFor VFD*E*C models, the factory setting is Group 1 Basic ParametersExplanation Settings Factory Group 2 Operation Method Parameters AVI2UP/DOWN For VFD*E*C models Explanation Settings Factory SettingGroup 3 Output Function Parameters Not for VFD*E*C Group 4 Input Function ParametersQuick Stop Only for VFD*E*C models Setting is 23. For VFD*E*C For VFD*E*C models Models, the factoryBit5=1MI6 used by PLC Group 5 Multi-Step Speeds Parameters Group 6 Protection ParametersExplanation Settings Factory Group 7 Motor Parameters FLASetting Group 8 Special Parameters Group 9 Communication Parameters Only for VFD*E*C Models Address only for VFD*E*C modelsOnly for VFD*E*C Group 10 PID Control ParametersParameters for Extension Card MO4/RA4 MO2/RA2MO3/RA3 MO5/RA5Explanation Settings Quick Stop Only for VFD*E*C models Group 13 PG function Parameters for Extension Card Fault CodesPLC not for VFD*E*C models Overheating Over currentOver voltage OverloadGFF hardware error Fault Fault Descriptions Corrective Actions Name OverloadCC current clamp OV hardware error OC hardware errorTemperature sensor error Fault Fault Descriptions Corrective Actions NamePhase error PID feedback signal errorDimensions are in mm inch FrameH1 H Frame C Unit mm inch