Delta Electronics VFD-XXXE quick start Explanation Settings Quick Stop Only for VFDEC models

Page 29

Pr.

Explanation

Settings

23:Quick Stop (Only for VFDEC models)

24:Download/execute/monitor PLC Program (PLC2) (NOT for VFD*E*C models)

25:Simple position function

26:OOB (Out of Balance Detection)

27:Motor selection (bit 0)

28:Motor selection (bit 1)

Factory Setting

NOTE

Group 12: Analog Input/Output Parameters for Extension Card

		0: Disabled
		1: Source of the 1st frequency
12.00	AI1 Function	2: Source of the 2nd frequency	0
	Selection	3: PID Set Point (PID enable)

		4: Positive PID feedback
		5: Negative PID feedback
12.01	AI1 Analog Signal	0: ACI2 analog current (0.0 ~ 20.0mA)	1
	Mode	1: AVI3 analog voltage (0.0 ~ 10.0V)

12.02	Min. AVI3 Input	0.0 to 10.0V	0.0
	Voltage

12.03	Min. AVI3 Scale	0.0 to 100.0%	0.0
	Percentage

12.04	Max. AVI3 Input	0.0 to 10.0V	10.0
	Voltage

12.05	Max. AVI3 Scale	0.0 to 100.0%	100.0
	Percentage

12.06	Min. ACI2 Input	0.0 to 20.0mA	4.0
	Current

12.07	Min. ACI2 Scale	0.0 to 100.0%	0.0
	Percentage

12.08	Max. ACI2 Input	0.0 to 20.0mA	20.0
	Current

12.09	Max. ACI2 Scale	0.0 to 100.0%	100.0
	Percentage

		0: Disabled
		1: Source of the 1st frequency
12.10	AI2 Function	2: Source of the 2nd frequency	0
	Selection	3: PID Set Point (PID enable)

		4: Positive PID feedback
		5: Negative PID feedback
12.11	AI2 Analog Signal	0: ACI3 analog current (0.0 ~ 20.0mA)	1
	Mode	1: AVI4 analog voltage (0.0 ~ 10.0V)

12.12	Min. AVI4 Input	0.0 to 10.0V	0.0
	Voltage

12.13	Min. AVI4 Scale	0.0 to 100.0%	0.0
	Percentage

12.14	Max. AVI4 Input	0.0 to 10.0V	10.0
	Voltage

12.15	Max. AVI4 Scale	0.0 to 100.0%	100.0
	Percentage

12.16	Min. ACI3 Input	0.0 to 20.0mA	4.0
	Current

12.17	Min. ACI3 Scale	0.0 to 100.0%	0.0
	Percentage

English- 29

Image 29

Contents Preface Voltage Class 115V Class SpecificationsGeneral Specifications SL2 VT2 TL3 WT3 Basic Wiring Diagram+/B1 Description of the Digital Keypad KPE-LE02 Optional PNP mode without external powerSignal Description To shift data Operation Steps of the Digital KeypadFrame Power Terminals Torque Wire Wire Type Power Terminals and Control TerminalsTerminal Symbol Terminal ExplanationsFrame Control Terminals Torque Specification for the Control TerminalsControl Terminals Explanations Group 0 User Parameters Summary of Parameter SettingsModels Explanation Settings FactoryNot for VFD*E*C models VFD*E*C modelsGroup 1 Basic Parameters For VFD*E*C models, the factory setting isExplanation Settings Factory AVI2 Group 2 Operation Method ParametersUP/DOWN Group 3 Output Function Parameters Explanation Settings Factory SettingFor VFD*E*C models Group 4 Input Function Parameters Not for VFD*E*CFor VFD*E*C For VFD*E*C models Models, the factory Quick Stop Only for VFD*E*C models Setting is 23.Bit5=1MI6 used by PLC Group 6 Protection Parameters Group 5 Multi-Step Speeds ParametersExplanation Settings Factory FLA Group 7 Motor ParametersSetting Group 8 Special Parameters Group 9 Communication Parameters Only for VFD*E*C Address only for VFD*E*C modelsOnly for VFD*E*C Models Group 10 PID Control ParametersParameters for Extension Card MO3/RA3 MO2/RA2MO4/RA4 MO5/RA5Explanation Settings Quick Stop Only for VFD*E*C models PLC not for VFD*E*C models Fault CodesGroup 13 PG function Parameters for Extension Card Over voltage Over currentOverheating OverloadCC current clamp OV hardware error Fault Fault Descriptions Corrective Actions Name OverloadGFF hardware error OC hardware errorPhase error Fault Fault Descriptions Corrective Actions NameTemperature sensor error PID feedback signal errorFrame Dimensions are in mm inchH1 H Frame C Unit mm inch