Delta Electronics VFD-XXXE quick start Setting

Page 23

	Pr.	Explanation	Settings	Factory	NOTE
	Pr.	Explanation	Settings	Setting	NOTE
				Setting
		Motor PTC
07.15		Overheat Warning	0.1~10.0V	1.2
		Level
		Motor PTC
07.16		Overheat Reset	0.1~5.0V	0.6
		Delta Level
07.17		Treatment of the	0: Warn and RAMP to stop	0
07.17		Motor PTC	1: Warn and COAST to stop	0
		Overheat	2: Warn and keep running
07.18		Motor Rated Current	30 %FLA to 120% FLA	FLA
		(Motor 1)
07.19		Motor No-Load	0%FLA to 99% FLA	0.4*FLA
07.19		Current (Motor 1)	0%FLA to 99% FLA	0.4*FLA
		Current (Motor 1)
07.20		Torque	0.0 to 10.0	0.0
07.20		Compensation	0.0 to 10.0	0.0
		(Motor 1)
		Slip Compensation
07.21		(Used without PG)	0.00 to 10.00	0.00
		(Motor 1)
		Motor Line-to-line	0~65535 mΩ
07.22		Resistance R1	0~65535 mΩ	0
		(Motor 1)
07.23		Motor Rated Slip	0.00 to 20.00 Hz	3.00
07.23		(Motor 1)	0.00 to 20.00 Hz	3.00
		(Motor 1)
07.24		Motor Pole Number	2 to 10	4
07.24		(Motor 1)	2 to 10	4
		(Motor 1)
07.25		Motor Rated Current	30 %FLA to 120% FLA	FLA
		(Motor 2)
07.26		Motor No-Load	0%FLA to 99% FLA	0.4*FLA
07.26		Current (Motor 2)	0%FLA to 99% FLA	0.4*FLA
		Current (Motor 2)
07.27		Torque	0.0 to 10.0	0.0
07.27		Compensation	0.0 to 10.0	0.0
		(Motor 2)
		Slip Compensation
07.28		(Used without PG)	0.00 to 10.00	0.00
		(Motor 2)
		Motor Line-to-line	0~65535 mΩ
07.29		Resistance R1	0~65535 mΩ	0
		(Motor 2)
07.30		Motor Rated Slip	0.00 to 20.00 Hz	3.00
07.30		(Motor 2)	0.00 to 20.00 Hz	3.00
		(Motor 2)
07.31		Motor Pole Number	2 to 10	4
07.31		(Motor 3)	2 to 10	4
		(Motor 3)
07.32		Motor Rated Current	30 %FLA to 120% FLA	FLA
		(Motor 3)
07.33		Motor No-Load	0%FLA to 99% FLA	0.4*FLA
07.33		Current (Motor 3)	0%FLA to 99% FLA	0.4*FLA
		Current (Motor 3)
07.34		Torque	0.0 to 10.0	0.0
07.34		Compensation	0.0 to 10.0	0.0
		(Motor 3)
		Slip Compensation
07.35		(Used without PG)	0.00 to 10.00	0.00
		(Motor 3)

English- 23

Image 23

Contents Preface Voltage Class 115V Class SpecificationsGeneral Specifications SL2 VT2 TL3 WT3 Basic Wiring Diagram+/B1 Description of the Digital Keypad KPE-LE02 Optional PNP mode without external powerSignal Description To shift data Operation Steps of the Digital KeypadTerminal Explanations Power Terminals and Control TerminalsFrame Power Terminals Torque Wire Wire Type Terminal SymbolFrame Control Terminals Torque Specification for the Control TerminalsControl Terminals Explanations Group 0 User Parameters Summary of Parameter SettingsVFD*E*C models Explanation Settings FactoryModels Not for VFD*E*C modelsGroup 1 Basic Parameters For VFD*E*C models, the factory setting isExplanation Settings Factory AVI2 Group 2 Operation Method ParametersUP/DOWN Group 3 Output Function Parameters Explanation Settings Factory SettingFor VFD*E*C models Group 4 Input Function Parameters Not for VFD*E*CFor VFD*E*C For VFD*E*C models Models, the factory Quick Stop Only for VFD*E*C models Setting is 23.Bit5=1MI6 used by PLC Group 6 Protection Parameters Group 5 Multi-Step Speeds ParametersExplanation Settings Factory FLA Group 7 Motor ParametersSetting Group 8 Special Parameters Group 9 Communication Parameters Group 10 PID Control Parameters Address only for VFD*E*C modelsOnly for VFD*E*C Only for VFD*E*C ModelsParameters for Extension Card MO5/RA5 MO2/RA2MO3/RA3 MO4/RA4Explanation Settings Quick Stop Only for VFD*E*C models PLC not for VFD*E*C models Fault CodesGroup 13 PG function Parameters for Extension Card Overload Over currentOver voltage OverheatingOC hardware error Fault Fault Descriptions Corrective Actions Name OverloadCC current clamp OV hardware error GFF hardware errorPID feedback signal error Fault Fault Descriptions Corrective Actions NamePhase error Temperature sensor errorFrame Dimensions are in mm inchH1 H Frame C Unit mm inch