Delta Electronics VFD-XXXE quick start Dimensions are in mm inch, Frame

Page 34

	Fault		Fault Descriptions			Corrective Actions
	Name		Fault Descriptions			Corrective Actions
	Name
			CANopen SYNC Time out		Check if CANopen synchronous message is
			(Only for VFDxxxExxC)		abnormal
			CANopen SDO Time out		Check if command channels are full
			(Only for VFDxxxExxC)
			CANopen SDO buffer		1.	Too short time between commands, please
			overflow (Only for			check SDO message sent from the master
			VFDxxxExxC)		2.	Reset CAN bus
			CAN bus off (Only for		1.	Check if it connects to terminal resistor
			VFDxxxExxC)		2.	Check if the signal is abnormal

3.Check if the master is connected

CAN Boot up fault (Only for	1.	Check if the master is connected
VFDxxxExxC)	2.	Reset CAN bus
Error communication protocol	Check if the communication protocol is correct
of CANopen (Only for
VFDxxxExxC)

Dimensions are in mm [inch]

Frame A

W

W1

D

D1

D2

H1 H

S1

S2

Unit: mm [inch]

	Frame	W	W1	H	H1	D	D1	D2	S1	S2
	A (A1)	72.0	60.0	142.0	120.0	152.0	50.0	4.5	5.2	5.2
		[2.83]	[2.36]	[5.59]	[4.72]	[5.98]	[1.97]	[0.18]	[0.20]	[0.20]

	A (A2)	72.0	56.0	155.0	143.0	111.5	9.5	-	5.3	-
		[2.83]	[2.20]	[6.10]	[5.63]	[4.39]	[0.37]		[0.21]

English- 34

Image 34

Contents Preface Specifications Voltage Class 115V ClassGeneral Specifications Basic Wiring Diagram SL2 VT2 TL3 WT3+/B1 Signal Description PNP mode without external powerDescription of the Digital Keypad KPE-LE02 Optional Operation Steps of the Digital Keypad To shift dataTerminal Symbol Power Terminals and Control TerminalsFrame Power Terminals Torque Wire Wire Type Terminal ExplanationsControl Terminals Explanations Specification for the Control TerminalsFrame Control Terminals Torque Summary of Parameter Settings Group 0 User ParametersNot for VFD*E*C models Explanation Settings FactoryModels VFD*E*C modelsFor VFD*E*C models, the factory setting is Group 1 Basic ParametersExplanation Settings Factory Group 2 Operation Method Parameters AVI2UP/DOWN For VFD*E*C models Explanation Settings Factory SettingGroup 3 Output Function Parameters Not for VFD*E*C Group 4 Input Function ParametersQuick Stop Only for VFD*E*C models Setting is 23. For VFD*E*C For VFD*E*C models Models, the factoryBit5=1MI6 used by PLC Group 5 Multi-Step Speeds Parameters Group 6 Protection ParametersExplanation Settings Factory Group 7 Motor Parameters FLASetting Group 8 Special Parameters Group 9 Communication Parameters Only for VFD*E*C Models Address only for VFD*E*C modelsOnly for VFD*E*C Group 10 PID Control ParametersParameters for Extension Card MO4/RA4 MO2/RA2MO3/RA3 MO5/RA5Explanation Settings Quick Stop Only for VFD*E*C models Group 13 PG function Parameters for Extension Card Fault CodesPLC not for VFD*E*C models Overheating Over current Over voltage OverloadGFF hardware error Fault Fault Descriptions Corrective Actions Name OverloadCC current clamp OV hardware error OC hardware errorTemperature sensor error Fault Fault Descriptions Corrective Actions NamePhase error PID feedback signal errorDimensions are in mm inch FrameH1 H Frame C Unit mm inch