| Pr. | Explanation | Settings | Factory | NOTE |
|
| Setting |
| ||||
|
|
|
|
|
| |
|
|
| 0: Baud rate 4800 bps |
|
|
|
09.08 | Transmission Speed | 1: Baud rate 9600 bps | 2 |
|
| |
for USB Card | 2: Baud rate 19200 bps |
|
| |||
|
| 3: Baud rate 38400 bps |
|
|
| |
|
|
|
|
|
| |
|
|
| 4: Baud rate 57600 bps |
|
|
|
|
|
| 0: 7,N,2 for ASCII |
|
|
|
|
|
| 1: 7,E,1 for ASCII |
|
|
|
|
|
| 2: 7,O,1 for ASCII |
|
|
|
|
|
| 3: 8,N,2 for RTU |
|
|
|
|
| Communication | 4: 8,E,1 for RTU |
|
|
|
|
| 5: 8,O,1 for RTU |
|
|
| |
09.09 | Protocol for USB | 1 |
|
| ||
6: 8,N,1 (Modbus, RTU) |
|
| ||||
|
| Card |
|
|
| |
|
| 7: 8,E,2 (Modbus, RTU) |
|
|
| |
|
|
|
|
|
| |
|
|
| 8: 8,O,2 (Modbus, RTU) |
|
|
|
|
|
| 9: 7,N,1 (Modbus, ASCII) |
|
|
|
|
|
| 10: 7,E,2 (Modbus, ASCII) |
|
|
|
|
|
| 11: 7,O,2 (Modbus, ASCII) |
|
|
|
|
| Transmission Fault | 0: Warn and keep operating |
|
|
|
09.10 | 1: Warn and ramp to stop | 0 |
|
| ||
Treatment for USB |
|
| ||||
2: Warn and coast to stop |
|
| ||||
|
| Card |
|
|
| |
|
| 3: No warning and keep operating |
|
|
| |
|
|
|
|
|
| |
09.11 | 0.1 ~ 120.0 seconds | 0.0 |
|
| ||
for USB Card | 0.0: Disable |
|
| |||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| COM port for PLC |
|
|
|
|
09.12 | Communication | 0: RS485 | 0 |
|
| |
(NOT for VFD*E*C | 1: USB card |
|
| |||
|
|
|
|
| ||
|
| models) |
|
|
|
|
|
| CANopen |
|
|
|
|
09.13 | Communication | 0: disable | 1 |
|
| |
Address (ONLY for | 1: 1 to 127 |
|
| |||
|
|
|
|
| ||
|
| VFD*E*C models) |
|
|
|
|
|
|
| 0: 1M |
|
|
|
|
| CANbus Baud Rate | 1: 500K |
|
|
|
|
| 2: 250K |
|
|
| |
09.14 | (ONLY for VFD*E*C | 5 |
|
| ||
3: 125K |
|
| ||||
|
| models) | 4: 100K |
|
|
|
|
|
| 5: 50K |
|
|
|
|
| Gain of CANbus |
|
|
|
|
09.15 | Frequency | 0.00~2.00 | 1.00 |
|
| |
(ONLY for VFD*E*C |
|
| ||||
|
| models) |
|
|
|
|
|
|
| bit 0 : CANopen Guarding Time out |
|
|
|
|
|
| bit 1 : CANopen Heartbeat Time out |
|
|
|
|
| CANbus Warning | bit 2 : CANopen SYNC Time out |
|
|
|
|
| bit 3 : CANopen SDO Time out | Read- |
|
| |
09.16 | (ONLY for VFD*E*C |
|
| |||
bit 4 : CANopen SDO buffer overflow | only |
|
| |||
|
| models) | bit 5 : CAN Bus Off |
|
|
|
|
|
| bit 6 : Error protocol of CANopen |
|
|
|
|
|
| bit 7 : CANopen boot up fault |
|
|
|
|
| Group 10 PID Control Parameters |
|
|
| |
English- 26