Delta Electronics VFD-XXXE Fault Codes, Group 13 PG function Parameters for Extension Card

Page 30

		Pr.	Explanation	Settings	Factory	NOTE
		Pr.	Explanation	Settings	Setting	NOTE
					Setting
12.18			Max. ACI3 Input	0.0 to 20.0mA	20.0
12.18			Current	0.0 to 20.0mA	20.0
			Current
12.19			Max. ACI3 Scale	0.0 to 100.0%	100.0
12.19			Percentage	0.0 to 100.0%	100.0
			Percentage
12.20			AO1 Terminal	0: AVO1	0
			AO1 Terminal	1: ACO1 (analog current 0.0 to 20.0mA)
			Analog Signal Mode	1: ACO1 (analog current 0.0 to 20.0mA)
			Analog Signal Mode	2: ACO1 (analog current 4.0 to 20.0mA)
				2: ACO1 (analog current 4.0 to 20.0mA)
12.21			AO1 Analog Output	0: Analog Frequency	0
12.21			Signal	1: Analog Current (0 to 250% rated current)	0
			Signal	1: Analog Current (0 to 250% rated current)
12.22			AO1 Analog Output	1 to 200%	100
12.22			Gain	1 to 200%	100
			Gain
12.23			AO2 Terminal	0: AVO2	0
			AO2 Terminal	1: ACO2 (analog current 0.0 to 20.0mA)
			Analog Signal Mode	1: ACO2 (analog current 0.0 to 20.0mA)
			Analog Signal Mode	2: ACO2 (analog current 4.0 to 20.0mA)
				2: ACO2 (analog current 4.0 to 20.0mA)
12.24			AO2 Analog Output	0: Analog Frequency	0
12.24			Signal	1: Analog Current (0 to 250% rated current)	0
			Signal	1: Analog Current (0 to 250% rated current)
12.25			AO2 Analog Output	1 to 200%	100
12.25			Gain	1 to 200%	100
			Gain
			Group 13: PG function Parameters for Extension Card
				0: Disabled
13.00			PG Input	1: Single phase	0
13.00			PG Input	2: Forward/Counterclockwise rotation	0
				2: Forward/Counterclockwise rotation
				3: Reverse/Clockwise rotation
	13.01		PG Pulse Range	1 to 20000	600
13.02			Motor Pole Number	2 to 10	4
13.02			(Motor 0)	2 to 10	4
			(Motor 0)
13.03			Proportional Gain	0.0 to 10.0	1.0
13.03			(P)	0.0 to 10.0	1.0
			(P)
	13.04		Integral Gain (I)	0.00 to 100.00 sec	1.00
			Speed Control
13.05			Output Frequency	0.00 to 100.00Hz	10.00
			Limit
13.06			Speed Feedback	0 to 9999 (*2ms)	500
13.06			Display Filter	0 to 9999 (*2ms)	500
			Display Filter
			Detection Time for	0.0: disabled
13.07			Feedback Signal	0.0: disabled	1
13.07			Feedback Signal	0.1 to 10.0 sec	1
			Fault	0.1 to 10.0 sec
			Fault
			Treatment of the	0: Warn and RAMP to stop
13.08			Feedback Signal	1: Warn and COAST to stop	1
			Fault	2: Warn and keep operation
13.09			Speed Feedback	0 to 9999 (*2ms)	16
13.09			Filter	0 to 9999 (*2ms)	16
			Filter
13.10			Source of the High-	0: PG card	Read
13.10			speed Counter	1: PLC (NOT for VFDEC models)	Only
			speed Counter	1: PLC (NOT for VFDEC models)	Only

Fault Codes

English- 30

Image 30

Contents Preface Specifications Voltage Class 115V ClassGeneral Specifications Basic Wiring Diagram SL2 VT2 TL3 WT3+/B1 PNP mode without external power Signal DescriptionDescription of the Digital Keypad KPE-LE02 Optional Operation Steps of the Digital Keypad To shift dataTerminal Symbol Power Terminals and Control TerminalsFrame Power Terminals Torque Wire Wire Type Terminal ExplanationsSpecification for the Control Terminals Control Terminals ExplanationsFrame Control Terminals Torque Summary of Parameter Settings Group 0 User ParametersNot for VFD*E*C models Explanation Settings FactoryModels VFD*E*C modelsFor VFD*E*C models, the factory setting is Group 1 Basic ParametersExplanation Settings Factory Group 2 Operation Method Parameters AVI2UP/DOWN Explanation Settings Factory Setting For VFD*E*C modelsGroup 3 Output Function Parameters Not for VFD*E*C Group 4 Input Function ParametersQuick Stop Only for VFD*E*C models Setting is 23. For VFD*E*C For VFD*E*C models Models, the factoryBit5=1MI6 used by PLC Group 5 Multi-Step Speeds Parameters Group 6 Protection ParametersExplanation Settings Factory Group 7 Motor Parameters FLASetting Group 8 Special Parameters Group 9 Communication Parameters Only for VFD*E*C Models Address only for VFD*E*C modelsOnly for VFD*E*C Group 10 PID Control ParametersParameters for Extension Card MO4/RA4 MO2/RA2MO3/RA3 MO5/RA5Explanation Settings Quick Stop Only for VFD*E*C models Fault Codes Group 13 PG function Parameters for Extension CardPLC not for VFD*E*C models Overheating Over currentOver voltage OverloadGFF hardware error Fault Fault Descriptions Corrective Actions Name OverloadCC current clamp OV hardware error OC hardware errorTemperature sensor error Fault Fault Descriptions Corrective Actions NamePhase error PID feedback signal errorDimensions are in mm inch FrameH1 H Frame C Unit mm inch