Barco R9002249 Connections, AC Power mains Cord Connection, Power Check, Switching On/Off

Page 11

Connections

3CONNECTIONS

AC Power (mains) Cord Connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the frontside of the projector.

V NOM 120/230 Volt
I MAX	7/5Amp
FREQ	50/60Hz

Power Check

Power voltage indication on sticker on the rear side of the projector. The power voltage is indicated by the art. no.

Warning !

Check if the indicated power voltage corresponds to that of the wall outlet.

Art. No. R9000972 must be connected to a 230 VAC power source. Art. No. R9000977 must be connected to a 120 VAC power source.

If the wall outlet voltage is different, call a qualified technician for power adaptation of the projector.

Switching On/Off

The projector is switched ON and OFF using the power (mains) switch ON/OFF.

Pressed : ON

Not pressed : OFF

The projector can start now in the 'operational mode' (image dis- played) or in the 'stand by mode', depending on the position of the 'power up' dip switch on the controller unit. This DIP switch must be set during installation by a qualified technician. If you want to change this start up mode, call a qualified technician.

Stand by indication lamp :

no light up : projector switched off

green color : projector in Operational mode

red color : projector is in Standby mode.

When starting up the projector, with the power switch or via the stand-by key, the projector can start up in two ways if the "CRT run in" cycle option is switched OFF.

-full white image (projector warm up) or

-immediately image display.

The way of starting up can be set in the service mode.

5975688 BARCOVISION 1609S 131097		3-1

Image 11

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUConnections AC Power mains Cord ConnectionPower Check Switching On/OffRemaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to portRED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUAddress How to display a projector address?How to program an address into the RCU? ProjectorBrightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingLine Doubler on Port 2 Video or S-VideoLine Doubler option Color SelectTop image focusing FocusingFocusing color select Midpoint focusingPhase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsRED on Green Convergence AdjustmentCoarse Convergence Adjustment ConvergenceVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service modeCopy a Block IdentificationCopy a block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocksRun time Change passwordChange Password Change LanguageUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycleProjector Warm Up CRT Drive ModeCRT Drive Mode Projector Address MESSAGES, Warnings and FailuresInput SourceIris FAN Failed WaitOptions Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card