Barco R9002240, R9002249 owner manual Left-Right east-west Adjustments, Left-Right E-W

Page 32

Random Access Adjustment Mode

Left-Right (east-west) Adjustments

Left-right adjustments affect only the vertical lines of the projected image. Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be corrected in the same manner. Convergence corrections are automatically disabled for the duration of these adjustments.

The following adjustments can be executed

-Vertical Centerline Bow

-Vertical Centerline Skew

-Side Bow

-Side Keystone

-Seagull correction

Push the control disk up or down to highlight LEFT-RIGHT (E/W) on the geometry menu and then press ENTER.

ENTER will select Left-Right adjustment menu

EXIT returns to random access adjustment mode main menu.

ADJUST returns to operational mode

The warning : "Use this correction to adjust the right side of the image" appears on the screen when selecting 'Side Bow' or 'Side Keystone'. When the right side is correctly adjusted, use 'Left Side Correction' to correct the left side of the image.

All adjustments are indicated on the screen with the function name, a bar scale and a number between 0 and 100.

Adjust the next alignments until the vertical lines are straight. For side bow and side keystone, look only to the right side of the image. To enter an alignment, push the control disk up or down to highlight a function and press ENTER to activate this function.

Press EXIT to return.

LEFT-RIGHT

V CENTERLINE BOW

V CENTERLINE SKEW

SIDE BOW

SIDE KEYSTONE

SEAGULL CORRECTION

Select with or then <ENTER> <EXIT> to return.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with

or

 

then <ENTER>

 

<EXIT>

LEFT-RIGHT

 

 

V CENTERLINE BOW

 

V CENTERLINE SKEW

 

SIDE BOW

 

SIDE KEYSTONE

 

SEAGULL CORRECTION

Warning : Use this correction to

adjust the right side of the image !

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

Corrects for curvature of the vertical lines in the middle of the image.

Corrects the tilting of the vertical lines in the middle of the image.

Corrects for curvature of the vertical lines on the right side

Corrects the keystone geometry correction of the vert. lines on the right side

Correct by pushing the control disk to the right

Correct by pushing the control disk to the left

6-10

 

5975688 BARCOVISION 1609S 131097

 

Image 32
Contents Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel TerminologyControl panel terminology Local Keypad built in RCU RCU control panel terminologyAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsRemaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a Composite Video source to port Connecting a S-Video or Video source to portRED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Battery installation in the RCU ControllingHow to use your RCU Projector AddressHow to display a projector address? How to program an address into the RCU?Projector AddressBrightness Analog Picture ControlsControlling chained projectors Start UP of the Adjustment Mode Adjustment ModeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting-Up the Random Access Adjustment modeOverview Random Access Adjustment mode EnterFrom next Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningColor Balance Color BalanceSync Fast/Slow Adjustment Clamp TuningPeaking PeakingPort 2 Video or S-Video Line Doubler optionColor Select Line Doubler onFocusing Focusing color selectMidpoint focusing Top image focusingPhase Geometry AdjustmentsHorizontal Phase Adjustment Raster Shift Adjustment Correct raster position Wrong raster positionLeft-Right east-west Adjustments LEFT-RIGHT E-WLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment SizeVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments BlankingConvergence Adjustment Coarse Convergence AdjustmentConvergence RED on GreenFine Convergence Adjustment Vertical CornersRandom Access Adjustment Mode Service Mode Starting up the Service modeOverview flowchart Service mode ServiceCopy a Block IdentificationCopy a block Deletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockChange password Change PasswordChange Language Run timeSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismG2 Adjust Gamma correctionsCRT run in cycle CRT RUN in CycleProjector Warm Up CRT Drive ModeCRT Drive Mode MESSAGES, Warnings and Failures InputSource Projector AddressWait Iris FAN FailedOptions Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitOrbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card