Barco R9002249, R9002240 owner manual Table of Contents

Page 5

			Table of Contents

Table	of contents			i
Safety	instructions		1-1
On safety			1-1
On installation			1-2
On servicing			1-2
On cleaning			1-2
On repacking			1-2
On illumination			1-2
Location and Functions of Control			2-1
Rear panel terminology			2-1
Front panel terminology			2-1
Control panel terminology			2-2
a. The Local Keypad			2-2
b. RCU control panel terminology			2-2
Connections			3-1
AC Power (mains) Cord Connection			3-1
Power Check			3-1
Switching On/Off			3-1
Signal Input Connection to the Projector :			3-2
Connecting a Composite Video source to port 1			3-3
Connecting a S-Video or Video source to port 2			3-3
Connecting a RGB Analog source to port 3			3-4
Connecting a RGB Analog source to port 4/5			3-4
Connecting a RGB Analog source with Tri-level sync to port 4/5.(option)			3-5
Connecting a Component Video source to port 4/5			3-5
Connecting a Component Video source with Tri-level sync to port 4/5.(Opion)			3-5
Peripheral equipment			3-6
Connecting a RCVDS 05 switcher to the projector			3-6
Connecting a VS05 switcher to the projector			3-6
Connecting an IR Remote Receiver to the projector			3-6
Controlling			4-1
Battery installation in the RCU			4-1
How to use your RCU			4-2
Projector Address			4-2
How to display a projector address?			4-3
How to program an address into the RCU?			4-3
Input selection			4-3
Analog Picture Controls			4-4
Controlling chained projectors			4-4
Start up of the Adjustment Mode			5-1
Adjustment Mode			5-1
Random Access Adjustment Mode			6-1
Starting-Up the Random Access Adjustment mode			6-1
Overview 'Random Access Adjustment' mode			6-1
Selecting Setup Pattern			6-3
Internal Cross Hatch Pattern			6-3
Random access adjustment mode selection menu			6-4
Picture Tuning			6-4
Color Balance			6-4
Sync Fast/Slow Adjustment			6-5
Peaking			6-5
Clamp Tuning			6-5
Port 2 : Video or S-Video			6-6
Line Doubler			6-6
Color Select			6-6
Focusing			6-7
Focusing color select			6-7
Blue on source			6-7
Geometry Adjustments			6-8
Horizontal Phase Adjustment			6-8
Raster Shift Adjustment			6-9
Left-Right (east-west) Adjustments			6-10
Seagull correction			6-11
Left Side Correction			6-11
Top-Bottom (north-south) Adjustments			6-12
Seagull Correction			6-13
Horizontal Size Adjustment			6-13
Vertical Linearity Adjustment			6-14
Vertical Size Adjustment			6-14
5975688 BARCOVISION 1609s 131097				i-1

Image 5

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUPower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsRemaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to portRED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUHow to program an address into the RCU? How to display a projector address?Projector AddressBrightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode EnterFrom next Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuColor Balance Color BalanceClamp Tuning Sync Fast/Slow AdjustmentPeaking PeakingLine Doubler option Port 2 Video or S-VideoColor Select Line Doubler onFocusing color select FocusingMidpoint focusing Top image focusingPhase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsCoarse Convergence Adjustment Convergence AdjustmentConvergence RED on GreenVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode ServiceCopy a Block IdentificationCopy a block Deleting block by block Deletion of blocksDeletion of all blocks Delete a BlockChange Password Change passwordChange Language Run timeUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentGamma corrections G2 AdjustCRT run in cycle CRT RUN in CycleProjector Warm Up CRT Drive ModeCRT Drive Mode Input MESSAGES, Warnings and FailuresSource Projector AddressIris FAN Failed WaitOptions Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card