Barco R9002249 Random Access Adjustment Mode, Starting-Up the Random Access Adjustment mode

Page 23

Random Access Adjustment Mode

6RANDOM ACCESS ADJUSTMENT MODE

Starting-Up the Random Access Adjustment mode.

Push the control disk up or down to highlight "RANDOM ACCESS" and then press

ENTER.

Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode.

ENTER continues to Setup Pattern Selection

EXIT returns to Operational mode

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS INSTALLATION SERVICE

IRIS

Source 01

Select with or

then <ENTER>

<EXIT> to return.

Overview 'Random Access Adjustment' mode

PICTURETUNING

RANDOM ACCESS	GEOMETRY
ADJUSTMENTMODE

SETUPPATTERNSELECTION

COLOR BALANCE

SYNC

PEAKING

CLAMPTUNING

LINEDOUBLER

PORT2

H PHASE

RASTERSHIFT

LEFT-RIGHT (E-W)

LEFTSIDECORRECTIONS

TOP-BOTTOM (N-S)

VCENTERLINEBOW

VCENTERLINESKEW

SIDEBOW

SIDEKEYSTONE

SEAGULLCORRECTION

LEFTKEYSTONE

LEFT BOW

HCENTERLINEBOW

HCENTERLINESKEW

TOPKEYSTONE

TOPBOW

BOTTOMKEYSTONE

BOTTOMBOW

SEAGULLCORRECTION

To next page

To next page

5975688 BARCOVISION 1609S 131097

6-1

Image 23

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUConnections AC Power mains Cord ConnectionPower Check Switching On/OffRemaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to portRED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUAddress How to display a projector address?How to program an address into the RCU? ProjectorBrightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingLine Doubler on Port 2 Video or S-VideoLine Doubler option Color SelectTop image focusing FocusingFocusing color select Midpoint focusingPhase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsRED on Green Convergence AdjustmentCoarse Convergence Adjustment ConvergenceVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service modeCopy a Block IdentificationCopy a block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocksRun time Change passwordChange Password Change LanguageUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycleProjector Warm Up CRT Drive ModeCRT Drive Mode Projector Address MESSAGES, Warnings and FailuresInput SourceIris FAN Failed WaitOptions Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card