Barco R9002249 Service Mode, Starting up the Service mode, Overview flowchart Service mode

Page 41

Service Mode

7SERVICE MODE

Starting up the Service mode.

Use the control disk to highlight 'Service' and then press ENTER.

Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also free available if you stay in the adjustment mode.

ENTER continues to the Service Mode main menu. EXIT returns to the Operational mode.

The service items are combined in two service menus. To switch from the first to the second menu or vice versa, push the control disk up or down to select 'more...'

Overview flowchart 'Service' mode.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

IRIS

source 1
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with	or
then <ENTER>
<EXIT> to	return.

SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
Select with	or
then <ENTER>
<EXIT> to	return.

SERVICEMODE

IDENTIFICATION

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

RUNTIME

G2ADJUSTMENT

GAMMACORRECTIONS

CRT RUN IN CYCLE

PROJECTORWARMUP

CRTDRIVEMODE

5975688 BARCOVISION 1609s 131097		7-1

Image 41

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUPower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsRemaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to portRED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUHow to program an address into the RCU? How to display a projector address?Projector AddressBrightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode EnterFrom next Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuColor Balance Color BalanceClamp Tuning Sync Fast/Slow AdjustmentPeaking PeakingLine Doubler option Port 2 Video or S-VideoColor Select Line Doubler onFocusing color select FocusingMidpoint focusing Top image focusingPhase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsCoarse Convergence Adjustment Convergence AdjustmentConvergence RED on GreenVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode ServiceCopy a Block IdentificationCopy a block Deleting block by block Deletion of blocksDeletion of all blocks Delete a BlockChange Password Change passwordChange Language Run timeUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentGamma corrections G2 AdjustCRT run in cycle CRT RUN in CycleProjector Warm Up CRT Drive ModeCRT Drive Mode Input MESSAGES, Warnings and FailuresSource Projector AddressIris FAN Failed WaitOptions Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card