Barco R9002249, R9002240 owner manual Connecting a Component Video source to port 4/5

Page 15

Connections

Connecting a RGB Analog source with Tri-level sync to port 4/5.

(option)

RGB analog input terminals with Tri level sync input or with Tri-level sync on green. The projector detects automati- cally where the sync signal is located.

RGB input selection :

(RG3sB : R, G, B signals with automatic Tri-level sync detection)

with the RCU or the build in RCU : press digit button 7

Connecting a Component Video source to port 4/5.

A component video (R-Y, Y, B-Y) with sync signals can be con- nected to the projector via the Port 4/5. The projector detects automatically where the sync signal is located.

To select the component video input :

with the RCU or the build in RCU : press digit button 6.

Connecting a Component Video source with Tri- level sync to port 4/5.

(Opion)

A component video (R-Y, Y, B-Y) with Tri-level sync signals can be connected to the projector via the Port 4/5. The projector detects automatically where the sync signal is located.

To select the component video input :

with the RCU or the build in RCU : press digit button 8.

5975688 BARCOVISION 1609S 131097		3-5

Image 15

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUConnections AC Power mains Cord ConnectionPower Check Switching On/OffSignal Input Connection to the Projector Pleaseuse Exitto Leave this ProcedureRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to portConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5RED Green Blue Connecting a Component Video source to port 4/5 Connecting a Rcvds 05 switcher to the projector Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUAddress How to display a projector address?How to program an address into the RCU? ProjectorAnalog Picture Controls Controlling chained projectorsBrightness Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingLine Doubler on Port 2 Video or S-VideoLine Doubler option Color SelectTop image focusing FocusingFocusing color select Midpoint focusingGeometry Adjustments Horizontal Phase AdjustmentPhase Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsSeagull correction Left Side CorrectionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsRED on Green Convergence AdjustmentCoarse Convergence Adjustment ConvergenceVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service modeIdentification Copy a blockCopy a Block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocksRun time Change passwordChange Password Change LanguageUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycleCRT Drive Mode CRT Drive ModeProjector Warm Up Projector Address MESSAGES, Warnings and FailuresInput SourceIris FAN Failed WaitOptions Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks and Source Numbers 90 Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card