Barco R9002249, R9002240 owner manual Adjustment procedure multiple projector installations

Page 55

Orbiting

Adjustment procedure multiple projector installations :

Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum.

Default setting of the Master projectorn see 'Stand-Alone projector'.

Highlight 'ADJUST DEVIATION' by pushing the control stick forward or backward and press ENTER.

When adjusting the horizontal and the vertical deviation, the picture moves in corresponding direction, allowing the set up of the deviation without orbiting operation.

Push the control stick to the right or backward to toggle between Hor. and Vert. deviation adjustment.

Adjust horizontal deviation by pushing the control stick to the left or to the right

Adjust vertical deviation by pushing the control stick forward or backward

SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH		OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH		OR
HORIZONTAL	WITH	OR
<EXIT> to	return.

Horizontal

orbitampl.

60

Vertical

orbitampl.

60

5975628 BARCOGRAPHICS 1209s 010797		A-3

Image 55

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUConnections AC Power mains Cord ConnectionPower Check Switching On/OffPleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to portConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUAddress How to display a projector address?How to program an address into the RCU? ProjectorControlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingLine Doubler on Port 2 Video or S-VideoLine Doubler option Color SelectTop image focusing FocusingFocusing color select Midpoint focusingHorizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsRED on Green Convergence AdjustmentCoarse Convergence Adjustment ConvergenceVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service modeCopy a block IdentificationCopy a Block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocksRun time Change passwordChange Password Change LanguageUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycleCRT Drive Mode CRT Drive ModeProjector Warm Up Projector Address MESSAGES, Warnings and FailuresInput SourceIris FAN Failed WaitOptions Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card