Barco R9002240, R9002249 owner manual Geometry Adjustments, Horizontal Phase Adjustment

Page 30

Random Access Adjustment Mode

Geometry Adjustments

The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color images : Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and Horizontal Phase.

Highlight GEOMETRY by pushing the control disk up or down and press ENTER to display the geometry menu.

ENTER will display Geometry menu

EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu

ADJUST returns to operational mode

Within the Geometry Adjustment menu, the following adjustments are available :

-Horizontal Phase (not for internal # pattern).

-Raster Shift

-Left-Right Corrections

-Left Side Corrections

-Top-Bottom Corrections

-Horizontal Size

-Vertical Linearity

-Vertical Size

-Blanking

The convergence corrections are disabled during geometry correc- tions. The blanking corrections are only enabled during the blanking adjustments.

Horizontal Phase Adjustment

Push the control disk up or down to highlight H PHASE on Geometry menu and then press ENTER.

Note : No horizontal phase adjustment is available on the internal # pattern.

For external sources :

If the raster shift is correctly adjusted, the H Phase text box is projected in the middle of the raster. At that moment, the "><" icon indicates the middle of the raster.

Adjust the H Phase control until the middle of the projected image is equal with the middle of >< icon.

Note :

RANDOM ACCESS

 

 

ADJUSTMENT MODE

 

 

PICTURE TUNING

 

 

GEOMETRY

 

 

CONVERGENCE

 

 

FOCUSING

 

 

COLOR SELECT

 

 

ORBITING

 

 

CONTR. MODULATION

 

 

SOFT EDGE

 

 

Select with

or

 

 

then <ENTER>

 

 

<EXIT> to

return.

GEOMETRY

 

 

H PHASE

 

 

RASTER SHIFT

 

 

LEFT-RIGHT (E-W)

 

LEFT SIDE CORRECTION

 

 

TOP-BOTTOM (N-S)

 

 

H SIZE

 

 

V LINEARITY

 

 

V SIZE

 

 

BLANKING

 

 

Select with

or

 

 

then <ENTER>

 

 

<EXIT> to

return.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with

or

then <ENTER>

<EXIT> to

return.

><

H PHASE

70

-if the genlocked pattern was selected, the external source will be displayed.

A bar scale and a number indicator (between 0 and 100) on the screen give a visual indication of the horizontal phase adjustment.

ENTER continues to geometry menu .

Push the control disk to the right to correct

Push the control disk to the left to correct

><

H PHASE

70

><

H PHASE

70

6-8

 

5975688 BARCOVISION 1609S 131097

 

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel TerminologyControl panel terminology Local Keypad built in RCU RCU control panel terminologySwitching On/Off AC Power mains Cord ConnectionPower Check ConnectionsSignal Input Connection to the Projector Pleaseuse Exitto Leave this ProcedureRemaining Projector Warm UP Time Connecting a Composite Video source to port Connecting a S-Video or Video source to portConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5RED Green Blue Connecting a Component Video source to port 4/5 Connecting a Rcvds 05 switcher to the projector Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Battery installation in the RCU ControllingHow to use your RCU Projector AddressProjector How to display a projector address?How to program an address into the RCU? AddressAnalog Picture Controls Controlling chained projectorsBrightness Start UP of the Adjustment Mode Adjustment ModeStart Up of the Adjustment Mode Overview Random Access Adjustment mode Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode EnterFrom next Selecting Setup Pattern Internal Cross Hatch PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingColor Select Port 2 Video or S-VideoLine Doubler option Line Doubler onMidpoint focusing FocusingFocusing color select Top image focusingGeometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift Adjustment Correct raster position Wrong raster positionLeft-Right east-west Adjustments LEFT-RIGHT E-WSeagull correction Left Side CorrectionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment SizeVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments BlankingConvergence Convergence AdjustmentCoarse Convergence Adjustment RED on GreenFine Convergence Adjustment Vertical CornersRandom Access Adjustment Mode Overview flowchart Service mode Service ModeStarting up the Service mode ServiceIdentification Copy a blockCopy a Block Deletion of all blocks Deletion of blocksDeleting block by block Delete a BlockChange Language Change passwordChange Password Run timeConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismCRT run in cycle G2 AdjustGamma corrections CRT RUN in CycleCRT Drive Mode CRT Drive ModeProjector Warm Up Source MESSAGES, Warnings and FailuresInput Projector AddressWait Iris FAN FailedOptions Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler KitOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks and Source Numbers 90 Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card
Top Page Image Contents