Barco R9002240 Port 2 Video or S-Video, Line Doubler option, Color Select, Line Doubler on

Page 28

Random Access Adjustment Mode

Port 2 : Video or S-Video

Port 2 can be used as a Video or S-Video input.

Highlight Port 2 by pushing the control disk up or down and press ENTER to toggle between VIDEO and S-VIDEO.

PICTURE TUNING
COLOR BALANCE
PORT2 : S-VIDEO
LINE DOUBLER : ON
Select with	or
<ENTER> to accept
<EXIT> to	return.

Line Doubler (option)

Line doubling is only possible for Video, S-Video, Component Video images on standard line frequency and RGB signals on 15 kHz.

To eliminate the video line patterns and to improve the image stability, the line doubler has to be switched on. The line doubler is default set in the ON position when starting up for the first time. The setting of the line doubler will be saved together with the source number. Each time this source number is selected, the last saved version will be loaded.

Highlight Line Doubler with the control disk and press ENTER to toggle between ON (active) and OFF (non active).

EXIT will return to the random access selection menu.

Color Select

Highlight COLOR SELECT by pushing the control disk up or down and press ENTER to display the color select menu.

ENTER continues to the color select menu

EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu

ADJUST returns to operational mode

Use the control disk to highlight a color (CRT) or combination of colors to display the projected image in that specific color.

To select a new color, press ENTER, the color selection menu appears again on the screen. To terminate the color select proce- dure, press EXIT.

ENTER continues with the selected color or color combination. EXIT returns to the Random access main menu.

PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PORT2 : S-VIDEO
LINE DOUBLER : ON
Select with	or
<ENTER> to accept
<EXIT> to	return.

RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with	or
then <ENTER>
<EXIT>	COLOR SELECT
	COLOR SELECT
	RED
	GREEN
	BLUE
	RED AND GREEN
	BLUE AND GREEN
	RED AND BLUE
	Select with	or
	<ENTER> to accept
	<EXIT> to	return.

6-6		5975688 BARCOVISION 1609S 131097

Image 28

Contents Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel TerminologyControl panel terminology Local Keypad built in RCU RCU control panel terminologyAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsPleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a Composite Video source to port Connecting a S-Video or Video source to portConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Battery installation in the RCU ControllingHow to use your RCU Projector AddressHow to display a projector address? How to program an address into the RCU?Projector AddressControlling chained projectors Analog Picture ControlsBrightness Start UP of the Adjustment Mode Adjustment ModeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting-Up the Random Access Adjustment modeOverview Random Access Adjustment mode EnterFrom next Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningColor Balance Color BalanceSync Fast/Slow Adjustment Clamp TuningPeaking PeakingPort 2 Video or S-Video Line Doubler optionColor Select Line Doubler onFocusing Focusing color selectMidpoint focusing Top image focusingHorizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift Adjustment Correct raster position Wrong raster positionLeft-Right east-west Adjustments LEFT-RIGHT E-WLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment SizeVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments BlankingConvergence Adjustment Coarse Convergence AdjustmentConvergence RED on GreenFine Convergence Adjustment Vertical CornersRandom Access Adjustment Mode Service Mode Starting up the Service modeOverview flowchart Service mode ServiceCopy a block IdentificationCopy a Block Deletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockChange password Change PasswordChange Language Run timeSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismG2 Adjust Gamma correctionsCRT run in cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeProjector Warm Up MESSAGES, Warnings and Failures InputSource Projector AddressWait Iris FAN FailedOptions Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitOrbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card