Barco R9002249, R9002240 MESSAGES, Warnings and Failures, Input, Source, Projector Address

Page 49

Messages, warnings and failures

8MESSAGES, WARNINGS AND FAILURES

INPUT 01

Fh= 15.6 kHz

Fv= 050 Hz

SOURCE 01

enter

password

x x x x

text on

text off

PROJECTOR

ADDRESS :

003

WARNING :

input not available

WARNING :

source not

available

WARNING :

invalid

key entry

When selecting a new source, information about this source will be displayed on the screen. Source number, horizontal and vertical fre- quencies of the displayed source.

Announcement of the selected source.

Message to enter your password. Password contains 4 digits.

These messages will be displayed on the screen when pushing the TEXT key.

Text ON : the 'bar scale indication' will be enabled during the change of an analog control in the 'opera- tional mode' + all warnings and failures will be displayed.

Text OFF : the 'bar scale indication' will be disabled during the change of an analog control in the 'opera- tional mode' + all warnings and failures will not be displayed.

Indication of the projector address when activating the 'ADDRESS' button on the RCU with a pencil or other small object.

When using the projector with the RCVDS, this warning will be dis- played when selecting an input slot of an RCVDS where the input board is missing.

The input is a valid input but the source is not connected to the input terminals or the input source is switched off.

When a wrong key is pressed on the RCU.

WARNING :

invalid

code entry

WARNING :

end of ad- just range

WARNING :

input no

longer available

WARNING :

input se- lector not available

WARNING :

invalid

frequency

input

table is deleted

FAILURE

I2C error

addr. : 7FH

FAILURE

short

circuit on

I2C bus

Message when the entered pass- word is wrong.

End of adjustment range.

Message will be displayed when the input source is no longer avail- able. The following message then appears: 'check input signal or select new source'.

It warns you to check the power connection or the power status of the RCVDS.

Next message will appear immediatly on the screen : 'go to stand-by'.

The entered frequency or applied frequency of the source is out of the projector's range.

Message to inform that selected table is deleted. This message will be followed by 'confirm message', on which the user has to answer.

Hardware failure. Call a qualified service technician for repair.

Hardware failure. Call a qualified service technician for repair.

5975688 BARCOVISION 1609s 131097		8-1

Image 49

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUPower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to portConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUHow to program an address into the RCU? How to display a projector address?Projector AddressControlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode EnterFrom next Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuColor Balance Color BalanceClamp Tuning Sync Fast/Slow AdjustmentPeaking PeakingLine Doubler option Port 2 Video or S-VideoColor Select Line Doubler onFocusing color select FocusingMidpoint focusing Top image focusingHorizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsCoarse Convergence Adjustment Convergence AdjustmentConvergence RED on GreenVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode ServiceCopy a block IdentificationCopy a Block Deleting block by block Deletion of blocksDeletion of all blocks Delete a BlockChange Password Change passwordChange Language Run timeUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentGamma corrections G2 AdjustCRT run in cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeProjector Warm Up Input MESSAGES, Warnings and FailuresSource Projector AddressIris FAN Failed WaitOptions Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card