Barco R9002249, R9002240 owner manual Connecting a Composite Video source to port

Page 13

Connections

Connecting a Composite Video source to port 1.

Composite video signals from a VCR, OFF air signal decoder, etc..

Video input selection :

with the RCU or the build in RCU : press digit button 1

* Note : if using the loop-through Video output, then set the Termination Switch to the "OFF" position.

Connecting a S-Video or Video source to port 2.

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.

4 pin connector configurations:

For S-video:		For video:
Pin 1: earth(ground) luminance		Pin 1:	earth(ground) video
Pin 2: earth(ground) chrominance	3	Pin 2:	notconnected
Pin 3: luminance signal(Y)	1	Pin 3:	video signal
Pin 3: luminance signal(Y)		Pin 3:	video signal
1Vpp±3dB	2	Pin 4: notconnected
Pin 4: chrominance signal(C)	4
Pin 4: chrominance signal(C)
300mVpp±3dB

Input selection

with the RCU or the build in RCU : press digit button 2 Depending on the priority setting in the Picture Tuning menu, Video or S-Video can be displayed.

If the setting is not correct, start up the adjustment mode by pushing on th ADJUST key.

Select 'Random Access' and press ENTER.

Select 'Selected source' and press ENTER.

Highlight 'Picture Tuning' and press ENTER.

Highlight Port 2 : Video and press ENTER to toggle between VIDEO or S-VIDEO.

Press EXIT to return.

Press ADJUST to return to operational mode.

*Note: When using the Port 2 loop-through output, set the Termination Switch in the "OFF" position.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

IRIS

Source 02 Choose a setup pattern

from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 02

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT
ORBITING
CONTR	PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PORT2 : S-VIDEO

LINE DOUBLER : ON

Select with or <ENTER> to accept <EXIT> to return.

5975688 BARCOVISION 1609S 131097		3-3

Image 13

Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUPower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to portConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUHow to program an address into the RCU? How to display a projector address?Projector AddressControlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode EnterFrom next Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuColor Balance Color BalanceClamp Tuning Sync Fast/Slow AdjustmentPeaking PeakingLine Doubler option Port 2 Video or S-VideoColor Select Line Doubler onFocusing color select FocusingMidpoint focusing Top image focusingHorizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsCoarse Convergence Adjustment Convergence AdjustmentConvergence RED on GreenVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode ServiceCopy a block IdentificationCopy a Block Deleting block by block Deletion of blocksDeletion of all blocks Delete a BlockChange Password Change passwordChange Language Run timeUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentGamma corrections G2 AdjustCRT run in cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeProjector Warm Up Input MESSAGES, Warnings and FailuresSource Projector AddressIris FAN Failed WaitOptions Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card