Barco R9002240, R9002249 owner manual Connecting a Rcvds 05 switcher to the projector

Page 16

Connections

PERIPHERAL EQUIPMENT

Connecting a RCVDS 05 switcher to the projector

-Up to 20 inputs with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules.

-Serial communication with the projector.

-Remote control buttons on the RCVDS to control the

projector (source selection and analog settings)

-The selected source number will be displayed on a 2 digit display and the selected input modules will be indicated with a LED on the rear.

For more information about the use of tje RCVDS, consult the Owner's Manual of the RCVDS.

Order number : RCVDS05 : R5975765

Connecting a VS05 switcher to the projector.

The VS05 can switch up to 5 Composite Video sources, 3 S-Video Sources and 1 RGB analog or component Video source to the projector. In addition, an audio signal associated with the source, can be switched to an audio amplifier.

Order number : R9827890.

For more information about the use of the VS05, consult the VS05 Owner's Manual, order number : R5975245.

Connecting an IR Remote Receiver to the projector.

This infra-red receiver unit makes it possible to control the projector from another room. There is a communication line cable between the IR receiver and the projector or the RCVDS. The infrared control information from the Remote Control Unit is sent to the IR Remote Receiver. The IR Remote Receiver 800 displays the selected source on a 7-segment display.

Order number : R9827515.

3-6		5975688 BARCOVISION 1609S 131097

Image 16

Contents Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel TerminologyControl panel terminology Local Keypad built in RCU RCU control panel terminologyAC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsPleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a Composite Video source to port Connecting a S-Video or Video source to portConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Battery installation in the RCU ControllingHow to use your RCU Projector AddressHow to display a projector address? How to program an address into the RCU?Projector AddressControlling chained projectors Analog Picture ControlsBrightness Start UP of the Adjustment Mode Adjustment ModeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting-Up the Random Access Adjustment modeOverview Random Access Adjustment mode EnterFrom next Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningColor Balance Color BalanceSync Fast/Slow Adjustment Clamp TuningPeaking PeakingPort 2 Video or S-Video Line Doubler optionColor Select Line Doubler onFocusing Focusing color selectMidpoint focusing Top image focusingHorizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift Adjustment Correct raster position Wrong raster positionLeft-Right east-west Adjustments LEFT-RIGHT E-WLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment SizeVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments BlankingConvergence Adjustment Coarse Convergence AdjustmentConvergence RED on GreenFine Convergence Adjustment Vertical CornersRandom Access Adjustment Mode Service Mode Starting up the Service modeOverview flowchart Service mode ServiceCopy a block IdentificationCopy a Block Deletion of blocks Deleting block by blockDeletion of all blocks Delete a BlockChange password Change PasswordChange Language Run timeSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismG2 Adjust Gamma correctionsCRT run in cycle CRT RUN in CycleCRT Drive Mode CRT Drive ModeProjector Warm Up MESSAGES, Warnings and Failures InputSource Projector AddressWait Iris FAN FailedOptions Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitOrbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card