Barco R9002240, R9002249 Orbiting Speed Toggle only in Master Orbiting, Orbiting Alignment

Page 54

Orbiting

Orbiting Speed Toggle (only in MASTER Orbiting)

Highlight 'SPEED : SLOW' with the control stick and press ENTER to set the ORBITING SPEED to Fast.

Highlight 'SPEED : FAST' with the control stick and press ENTER to set the ORBITING SPEED to Slow

ENTER continues to Set up Orbiting

EXIT returns to path selection menu

ADJUST returns to operational mode.

MASTER ORBITING

CHANGE TO MASTER

MODE : ON

 

SPEED : FAST

 

ADJUST DEVIATION

SELECT WITH

OR

THEN <ENTERN>

DEVIATION ADJUST :

VERTICAL WITH

OR

HORIZONTAL

WITH

OR

<EXIT>

to return.

Orbiting Alignment

Preparation :

Before proceeding to the alignment of the Orbiting default settings, be sure that the Horizontal Phase and the Raster shift are correctly aligned with the Orbiting mode set to OFF.

This alignment must be performed in case of a multiple projector installation with Master and Slave projectors in order to ensure a correct operation of the Orbiting for all projectors.

Adjustment procedure Stand-Alone projector :

Highlight 'ADJUST DEVIATION' with the control stick and press

ENTER.

When adjusting the horizontal and the vertical deviation, the picture moves in the corresponding direction, allowing the set up of the deviation without orbiting operation.

Push the control stick to the right or backward to toggle between Hor. and Vert. deviation andjustment.

Adjust horizontal deviation by pushing the control stick to the left or to the right

Adjust vertical deviation by pushing the control stick forward or backward

SLAVE ORBITING

CHANGE TO MASTER

ADJUST DEVIATION

SELECT WITH

OR

THEN <ENTERN>

DEVIATION ADJUST :

VERTICAL WITH

OR

HORIZONTAL

WITH

OR

<EXIT> to

return.

Horizontal

orbitampl.

60

Vertical

orbitampl.

60

A-2

 

5975268 BARCOGRAPHICS 1209s 010797

 

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Vision 1609s R9002240 R9002249 Page Barco Projection Systems Date Art. No 131097 R5975688Page Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Location and Function of Controls Rear Panel TerminologyControl panel terminology Local Keypad built in RCU RCU control panel terminologySwitching On/Off AC Power mains Cord ConnectionPower Check ConnectionsSignal Input Connection to the Projector Pleaseuse Exitto Leave this ProcedureRemaining Projector Warm UP Time Connecting a Composite Video source to port Connecting a S-Video or Video source to portConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5RED Green Blue Connecting a Component Video source to port 4/5 Connecting a Rcvds 05 switcher to the projector Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Battery installation in the RCU ControllingHow to use your RCU Projector AddressProjector How to display a projector address?How to program an address into the RCU? AddressAnalog Picture Controls Controlling chained projectorsBrightness Start UP of the Adjustment Mode Adjustment ModeStart Up of the Adjustment Mode Overview Random Access Adjustment mode Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode EnterFrom next Selecting Setup Pattern Internal Cross Hatch PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingColor Select Port 2 Video or S-VideoLine Doubler option Line Doubler onMidpoint focusing FocusingFocusing color select Top image focusingGeometry Adjustments Horizontal Phase AdjustmentPhase Raster Shift Adjustment Correct raster position Wrong raster positionLeft-Right east-west Adjustments LEFT-RIGHT E-WSeagull correction Left Side CorrectionLeft Side Correction Top-Bottom north-south Adjustments Horizontal Size Adjustment SizeVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments BlankingConvergence Convergence AdjustmentCoarse Convergence Adjustment RED on GreenFine Convergence Adjustment Vertical CornersRandom Access Adjustment Mode Overview flowchart Service mode Service ModeStarting up the Service mode ServiceIdentification Copy a blockCopy a Block Deletion of all blocks Deletion of blocksDeleting block by block Delete a BlockChange Language Change passwordChange Password Run timeConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismCRT run in cycle G2 AdjustGamma corrections CRT RUN in CycleCRT Drive Mode CRT Drive ModeProjector Warm Up Source MESSAGES, Warnings and FailuresInput Projector AddressWait Iris FAN FailedOptions Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler KitOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks and Source Numbers 90 Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card
Top Page Image Contents