Barco R9002249 Focusing color select, Midpoint focusing, Top image focusing, Blue on source

Page 29

Random Access Adjustment Mode

Focusing

Before starting the 'focusing' adjustment, be sure the lenses are correctly focused.

Push the control disk up or down to select 'Focusing' and press

ENTER.

ENTER continues to the Focusing color select menu.

EXIT returns to Internal Crosshatch Selection or Setup Pattern Selection menu.

ADJUST returns to operational mode.

Focusing color select.

The focusing has to be done for the three colors separately. Therefore, start by selecting Green by pushing the control disk up or down and adjust Midpoint, top, bottom left and right focusing.

Return to this focusing color select menu and continue with Red and Blue. Repeat for both colors Midpoint, top, bottom left and right focusing.

ENTER selects the focusing menu for the selected color. EXIT returns to the Random access main menu.

RANDOM ACCESS

 

ADJUSTMENT MODE

 

PICTURE TUNING

 

GEOMETRY

 

 

CONVERGENCE

 

FOCUSING

 

 

COLOR SELECT

 

ORBITING

 

 

CONTR. MODULATION

 

SOFT EDGE

 

 

Select with

or

 

then <ENTER>

 

<EXIT>

FOCUSING

 

RED

 

GREEN

 

BLUE

 

BLUE ON SOURCE

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

Midpoint focusing

Push the control disk up or down to select midpoint and press ENTER continue with the midpoint focusing.

Adjust by pushing the control disk to the left or to the right until the center of the image is sharp.

Press ENTER to return to the focusing menu.

Top image focusing

The same procedure has to be repeated as for the midpoint focusing. Push the control disk up or down and press ENTER to continue to the top focusing.

Push the control disk to the left or to the right to adjust the top focusing. Adjust until the upper part of the image is sharp.

ENTER to return to the Green Focusing menu.

Bottom image focusing

The same procedure has to be repeated as for the midpoint focusing. Push the control disk up or down to select bottom and press ENTER to continue to the bottom focusing.

Push the control disk up or down to adjust the bottom focusing. Adjust until the lower part of the image is sharp.

ENTER to return to the Green Focusing menu.

FOCUSING

 

 

RED

 

 

GREEN

 

 

BLUE

 

 

BLUE ON SOURCE

 

Select with

or

 

then

GREEN FOCUSING

<EXIT>

 

 

 

MIDPOINT

 

TOP

 

BOTTOM

 

LEFT

 

RIGHT

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

Left image focusing

The same procedure has to be repeated as for the midpoint focusing. Push the control disk up or down to select LEFT and press ENTER to continue to the left focusing.

Push the control disk up or down to adjust the left focusing. Adjust until the left part of the image is sharp.

ENTER to return to the Green Focusing menu.

Right image focusing

The same procedure has to be repeated as for the midpoint focusing. Push the control disk up or down to select RIGHT and press ENTER to continue to the right focusing.

Push the control disk to the left or to the right to adjust the right focusing. Adjust until the right part of the image is sharp. ENTER to return to the Green Focusing menu.

5975688 BARCOVISION 1609S 131097

When on the Green Focusing menu, press EXIT to return to the focusing color select menu and continue with the other colors.

Blue on source

After focusing the three color, and a discoloring on a normal image is still visible, select 'Blue on source' on the Focusing menu and repeat the above steps for Midpoint, top, bottom left and right focusing.

Press EXIT to return to focusing menu.

6-7

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUPower Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsRemaining Projector Warm UP Time Signal Input Connection to the ProjectorPleaseuse Exitto Leave this Procedure Connecting a S-Video or Video source to port Connecting a Composite Video source to portRED Green Blue Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUHow to program an address into the RCU? How to display a projector address?Projector AddressBrightness Analog Picture ControlsControlling chained projectors Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting-Up the Random Access Adjustment mode Random Access Adjustment ModeOverview Random Access Adjustment mode EnterFrom next Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuColor Balance Color BalanceClamp Tuning Sync Fast/Slow AdjustmentPeaking PeakingLine Doubler option Port 2 Video or S-VideoColor Select Line Doubler onFocusing color select FocusingMidpoint focusing Top image focusingPhase Geometry AdjustmentsHorizontal Phase Adjustment Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsCoarse Convergence Adjustment Convergence AdjustmentConvergence RED on GreenVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Starting up the Service mode Service ModeOverview flowchart Service mode ServiceCopy a Block IdentificationCopy a block Deleting block by block Deletion of blocksDeletion of all blocks Delete a BlockChange Password Change passwordChange Language Run timeUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentGamma corrections G2 AdjustCRT run in cycle CRT RUN in CycleProjector Warm Up CRT Drive ModeCRT Drive Mode Input MESSAGES, Warnings and FailuresSource Projector AddressIris FAN Failed WaitOptions Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Orbiting Source numbers 90 Adjustment Blocks and Source Numbers 90Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card
Top Page Image Contents