Barco R9002249 How to display a projector address?, How to program an address into the RCU?

Page 19

Controlling

How to display a projector address?

Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds.

PROJECTOR

ADDRESS

001

To continue using your RCU, it is necessary to enter the same address with the digit buttons (address between 0 and 9). For exemple, if the Adrress Key displays projector address 003, then press the "3" digit button on the RCU to set the RCU's address to match the projector's address.

How to program an address into the RCU?

Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons. That address can be any digit between 0 and 9.

When programming '0', zero address, the RCU will control a projector regardless of the projector's address. This feature allows multiple projectors with different addresses to be controlled by a single RCU.

Input selection

Port No

Projector input

Press Digit

 

 

 

 

Button

 

 

 

 

 

1

Comp. Video

1

 

2

S-Video1/Comp. Video*

2

 

3

RGB2

3

 

4/5

RGB2

4 or 5

 

4/5

Component video3

6

 

 

 

 

 

 

 

4/5

RGB with Tri level sync4

7

 

 

4/5

Component video

 

 

 

 

with Tri-level sync5

8

 

 

 

 

 

 

Only available when the optional Tri-level sync module is installed.

1Input signal Y/C (luma/chroma)

2Input signal : R, G and B with automatic sync detection between seperate sync (separate composite sync or with separate Hor

and Vert. sync) or sync on green (composite sync).

3Input signal : R-Y, Y and B-Y with separate composite sync or with separate Hor and Vert. sync or with composite sync on Y.

4Input signal : R, G and B with separate Tri level sync or with Tri- level sync on green.

5Input signal : R-Y, Y and B-Y with separate Tri level sync or with composite Tri-level sync.

*Video or S-Video : switchable in the Picture Tuning menu.

5975688 BARCOVISION 1609S 131097

With the digit buttons on the RCU, it is possible to select input sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S.

When a valid and available source is selected, there will be informa- tion displayed on the screen about that source (if "Text" is on). This information includes :

-source number

-horizontal frequency

-vertical frequency

Source 2

Fh= 15.6 kHz

Fv= 60 Hz

When the entry is a non valid source

number, a warning appears on the screen : 'input not available'.

WARNING input not available

When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the source

WARNING source not available

becomes available. A message 'source not available' will be dis- played for a short time.

4-3

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Vision 1609s R9002240 R9002249 Page Date Art. No 131097 R5975688 Barco Projection SystemsPage Table of Contents Appendix B Adjsutment Blocks and Source Numbers Safety Instructions On cleaning Rear Panel Terminology Location and Function of ControlsRCU control panel terminology Control panel terminology Local Keypad built in RCUConnections AC Power mains Cord ConnectionPower Check Switching On/OffPleaseuse Exitto Leave this Procedure Signal Input Connection to the ProjectorRemaining Projector Warm UP Time Connecting a S-Video or Video source to port Connecting a Composite Video source to portConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portRED Green Blue Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to the projector Connecting a Rcvds 05 switcher to the projectorConnecting an IR Remote Receiver to the projector Controlling Battery installation in the RCUProjector Address How to use your RCUAddress How to display a projector address?How to program an address into the RCU? ProjectorControlling chained projectors Analog Picture ControlsBrightness Adjustment Mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Enter Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning PeakingLine Doubler on Port 2 Video or S-VideoLine Doubler option Color SelectTop image focusing FocusingFocusing color select Midpoint focusingHorizontal Phase Adjustment Geometry AdjustmentsPhase Correct raster position Wrong raster position Raster Shift AdjustmentLEFT-RIGHT E-W Left-Right east-west AdjustmentsLeft Side Correction Seagull correctionLeft Side Correction Top-Bottom north-south Adjustments Size Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentBlanking Blanking AdjustmentsRED on Green Convergence AdjustmentCoarse Convergence Adjustment ConvergenceVertical Corners Fine Convergence AdjustmentRandom Access Adjustment Mode Service Service ModeStarting up the Service mode Overview flowchart Service modeCopy a block IdentificationCopy a Block Delete a Block Deletion of blocksDeleting block by block Deletion of all blocksRun time Change passwordChange Password Change LanguageUndo Convergence Midposition Set to midpositionUndo Midposition Convergence MidDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle G2 AdjustGamma corrections CRT run in cycleCRT Drive Mode CRT Drive ModeProjector Warm Up Projector Address MESSAGES, Warnings and FailuresInput SourceIris FAN Failed WaitOptions Line Doubler Kit Magik InterfaceCeiling Mount kit CM100 Orbiting KitMaster/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting optionOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Orbiting Adjustment Blocks memory blocks Adjustment Blocks and Source Numbers 90Source numbers 90 Adjustment Blocks and Source Numbers Insert Card
Top Page Image Contents