Planar Dome EX manual EMI shielding No emission of low-level radiation Temperature

Page 31

Power Supply

CAUTION: Use only the power adapter supplied with the Dome E3 display unit; Ault MW122RA1223F52.

Category

Characteristic Item

Specification

 

 

 

Power input

Voltage selection

Auto-ranging

requirements

Voltage

100 – 240V AC

 

 

Current

2.0 A

 

Frequency

50 to 60 Hz

 

 

 

Power output

Voltage

12 V DC ±5%

requirements

Current

10.0 A (120 W)

 

 

 

 

Physical

Size

228.6 mm x 76.2 mm x 50.8 mm

 

 

(9 in x 3 in x 2 in)

 

Weight

1.3 kg (2.75 lb)

 

 

 

Reliability

Characteristic item

Specification

 

 

Display

MTBF >50,000 hours

 

 

Backlight

MTBF 50,000 hours to 50% brightness with backlight on continuously

 

 

Environment

Characteristic item

 

Specification

 

 

 

EMI shielding

 

No emission of low-level radiation

 

 

 

Temperature

operating

0° C to 40° C

 

storage

-10° to 60° C

 

 

 

Humidity

operating

10% to 80% Relative Humidity

 

 

(non-condensing)

 

storage

5% to 90% Relative Humidity

 

 

(non-condensing)

 

 

 

Dome E3 Specification 21

Image 31
Contents User’s Guide Dome EX DisplayPlanar Systems, Inc. All rights reserved Contents Product Information Intended use Symbol explanationsSafety tips Safety precautionsPreventing fire and injury Unpacking and handling tipsCleaning the display Disposal information Shipping/storing the displayDVI cable About the Display System Requirements Display Components Viewing angle Orientation modeDisplay Positions Tilt range Height rangeUSB hub Desk Stand FeaturesStand height lock Stand cable coverInstalling the Display Tips Set the DIP Switch on the Dome DX2 BoardTo install the display controller Install the Display ControllerTo connect the cables Connect the Video and Power CablesTo change the display properties Install the Dome DX Display DriverTo install the driver To enable the displayTo set driver options To set the resolution and paletteAuto-orientation To set brightnessTo configure the display Install the AX3 Display DriverTo set the display mode manually To adjust the display propertiesTo use a dual-display configuration Appendix Problem Possible Cause Solution TroubleshootingCategory Characteristic Item Specification Dome E2 SpecificationReliability Power SupplyEnvironment Model Dome E3 SpecificationDome E3 Specification Dome E3 Specification EMI shielding No emission of low-level radiation Temperature Dome E3c Specification Display Mtbf 30,000 hours Backlight Dome E5 Specification Dome E5 Specification Video Modes Details of DIN connectors Connector PortsLED Status Lights LED a status information after initial power-on Power-up sequence information from LEDLED B status information after initial power-on Single Desktop To set the display resolutionRestoring dual heads To change the configuration to single desktopSystem configuration requirement Auto-InstallationInstallation options Prompting user response during Fastinst.bat To remove the Dome DX driver Display Driver RemovalTo remove the AX3 driver Power Management Grayscale Palette Options Nonlinear static gray palette Palette options with multiple displaysDesktop icons Dynamic gray paletteStatic gray palette Index Using single desktop Canada, European Union, United States Regulatory CompliancePage Fax + 358 9 420 EU Declaration of Conformity for Medical Application FCC Compliance Statement Korea AustralianChina JapanStandard Warranty Return Procedure Standard WarrantySummary Limitation of Implied Warranties Summary Limitations and Exclusions of Dome DisplaysEffect of Local Law Exclusion of DamagesMedicalsales@planar.com Medicalsupport@planar.com