InFocus XS1 manual Connecting a Component Video source device

Page 19

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue; and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the D-SUB/COMP. IN socket on the projector.

3.If you wish to make use the projector (mixed mono) speaker, take a suitable audio cable and connect one end of the cable to the audio output sockets of the video device, and the other end to the AUDIO socket of the projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 48 for details.

The final connection path should be like that shown in the following diagram:

AV device

Component Video to VGA (D-Sub) adaptor cable

Audio cable

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 16 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 19

Image 19

Contents Reference Guide Table of contents Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsFreeze Remote controlDigital Zoom buttons + Keystone buttons UpReplacing the remote control battery Remote control effective rangeFront Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a locationObtaining a preferred projected image size Page Screen diagonal Connecting a computer Connecting a computer or monitorConnection Iii Connecting a monitor Better video quality Connecting Video source devicesConnecting audio Best video qualityConnecting a DVI source device Connection To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationSub-menu Using the menusRemoving the control keypad on the projector Using a security cable lockUtilizing the password function Securing the projectorIf you forget the password Setting a passwordHighlight Change Security Settings and press Mode/Enter Changing the password Entering the password recall procedureDisabling the password function DVI-A DVI-D Switching input signalChanging Color Space Creating your own startup screenFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Page About the aspect ratio Selecting the aspect ratioYPbPr/S-Video/Video/HDCP Signal Input Selecting a picture modePicture modes for different types of signals PC/DVI-A/DVI-D Signal InputSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes 3D Color Management Adjusting BrilliantColorSelecting a color temperature About color temperaturesPress Mode/Enter and the 3D Color Management page displays Enter to display the Presentation Timer Setting the presentation timerGo to the System Setup Basic Presentation Timer menu and press ModeLocking control keys To cancel the timer, perform the following stepsFreezing the image Operating in a high altitude environment Hiding the imageMuting the sound Adjusting the soundAdjusting the sound level Personalizing the projector menu displayShutting down the projector Menu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Current System Information menuStatus Care of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screw that secures the lamp Resetting the lamp timerIndicators No picture TroubleshootingRemote control does not work Projector does not turn onProjector specifications SpecificationsSupported timing for PC including DVI-D input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for Component-YPbPrinput Signal Format Horizontal Vertical Frequency Frequency kHzSupported timing for Video and S-Video inputs Copyright Copyright informationDisclaimer