InFocus XS1 manual Fine-tuning the image quality in user modes

Page 35

Fine-tuning the image quality in user modes

According to the detected signal type, there are some user-definable functions available when User 1 or User 2 is selected. You can make adjustments to these functions based on your needs.

Adjusting Brightness

Highlight Brightness in the PICTURE menu and adjust the values by pressing / on the projector or remote control.

The higher the value, the brighter the image. And lower the setting, darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible.

+30

 

 

+50

 

 

+70

 

 

 

 

Adjusting Contrast

Highlight Contrast in the PICTURE menu and adjust the values by pressing / on the projector or remote control.

The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment.

+30

 

 

+50

 

 

+70

Adjusting Color

Highlight Color in the PICTURE menu and adjust the values by pressing / on the projector or remote control.

Lower setting produces less saturated colors; setting to the minimum value makes the image black and white. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic.

Adjusting Tint

Highlight Tint in the PICTURE menu and adjust the values by pressing / on the projector or remote control.

The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes.

Adjusting Sharpness

Highlight Sharpness in the PICTURE menu and adjust the values by pressing /

on the projector or remote control.

The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes.

Operation 35

Image 35
Contents Reference Guide Table of contents Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsFreeze Remote controlDigital Zoom buttons + Keystone buttons UpReplacing the remote control battery Remote control effective rangeFront Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a locationObtaining a preferred projected image size Page Screen diagonal Connection Connecting a computer or monitorConnecting a computer Iii Connecting a monitor Better video quality Connecting Video source devicesConnecting audio Best video qualityConnecting a DVI source device Connection To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationSub-menu Using the menusRemoving the control keypad on the projector Using a security cable lockUtilizing the password function Securing the projectorHighlight Change Security Settings and press Mode/Enter Setting a passwordIf you forget the password Disabling the password function Entering the password recall procedureChanging the password DVI-A DVI-D Switching input signalChanging Color Space Creating your own startup screenFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Page About the aspect ratio Selecting the aspect ratioYPbPr/S-Video/Video/HDCP Signal Input Selecting a picture modePicture modes for different types of signals PC/DVI-A/DVI-D Signal InputSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes 3D Color Management Adjusting BrilliantColorSelecting a color temperature About color temperaturesPress Mode/Enter and the 3D Color Management page displays Enter to display the Presentation Timer Setting the presentation timerGo to the System Setup Basic Presentation Timer menu and press ModeFreezing the image To cancel the timer, perform the following stepsLocking control keys Operating in a high altitude environment Hiding the imageMuting the sound Adjusting the soundAdjusting the sound level Personalizing the projector menu displayShutting down the projector Menu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Status Information menuCurrent System Care of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screw that secures the lamp Resetting the lamp timerIndicators No picture TroubleshootingRemote control does not work Projector does not turn onProjector specifications SpecificationsSupported timing for PC including DVI-D input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for Video and S-Video inputs Signal Format Horizontal Vertical Frequency Frequency kHzSupported timing for Component-YPbPrinput Disclaimer Copyright informationCopyright