InFocus XS1 manual Replacing the lamp

Page 53

Replacing the lamp

WARNING

Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.

•To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

•To assure optimal performance from the projector, it is recommended that you purchase the InFocus projector lamp for lamp replacement.

•If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp.

1.Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.Use a coin to turn the screw counterclockwise until the lamp cover

loosens.

3.Remove the lamp cover from the projector.

WARNING

• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

Maintenance 53

Image 53

Contents Reference Guide Table of contents Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsDigital Zoom buttons + Remote controlKeystone buttons Up FreezeReplacing the remote control battery Remote control effective rangePositioning your projector Set Rear Ceiling in the System Setup BasicChoosing a location Front TableObtaining a preferred projected image size Page Screen diagonal Connection Connecting a computer or monitorConnecting a computer Iii Connecting a monitor Connecting audio Connecting Video source devicesBest video quality Better video qualityConnecting a DVI source device Connection To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationSub-menu Using the menusUtilizing the password function Using a security cable lockSecuring the projector Removing the control keypad on the projectorHighlight Change Security Settings and press Mode/Enter Setting a passwordIf you forget the password Disabling the password function Entering the password recall procedureChanging the password DVI-A DVI-D Switching input signalChanging Color Space Creating your own startup screenAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Page About the aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC/DVI-A/DVI-D Signal Input YPbPr/S-Video/Video/HDCP Signal InputSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Selecting a color temperature Adjusting BrilliantColorAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Go to the System Setup Basic Setting the presentation timerPresentation Timer menu and press Mode Enter to display the Presentation TimerFreezing the image To cancel the timer, perform the following stepsLocking control keys Operating in a high altitude environment Hiding the imageAdjusting the sound level Adjusting the soundPersonalizing the projector menu display Muting the soundShutting down the projector Menu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Status Information menuCurrent System Care of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screw that secures the lamp Resetting the lamp timerIndicators Remote control does not work TroubleshootingProjector does not turn on No pictureProjector specifications SpecificationsTiming chart DimensionsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC including DVI-D inputSupported timing for Video and S-Video inputs Signal Format Horizontal Vertical Frequency Frequency kHzSupported timing for Component-YPbPrinput Disclaimer Copyright informationCopyright