InFocus XS1 manual Setting the presentation timer, Go to the System Setup Basic

Page 38

Setting the presentation timer

The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.

Go to the SYSTEM SETUP: Basic >

Presentation Timer

 

Presentation Timer menu and press Mode/

 

Timer Period

15

 

Enter to display the Presentation Timer

Timer Display

Always

 

Timer Position

Top-Left

 

page.

Timer Counting Direction

Count Down

2.

Sound Reminder

Off

Highlight Timer Period and decide the time

On

Off

period by pressing / . The length of time

MENU Back

 

can be set from 1 to 5 minutes in 1-minute

 

increments and 5 to 240 minutes in 5-minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing / .

Selection

Description

Always

Displays the timer on screen throughout the presentation time.

1 min/2 min/3 min

Displays the timer on screen in the last 1/2/3 minute(s).

Never

Hides the timer throughout the presentation time.

4.Press to highlight Timer Position and set the timer position by pressing

/ .

Top-Left Bottom-Left Top-Right Bottom-Right

5.Press to highlight Timer Counting Direction and select your desired counting direction by pressing / .

Selection

Description

Count Up

Increases from 0 to the preset time.

Count down

Decreases from the preset time to 0.

6.Press to highlight Sound Reminder and decide if you want to activate sound reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

7.To activate the presentation timer, press and press / to highlight On and press Mode/Enter.

8.A confirmation message displays. Highlight Yes and press Mode/Enter to confirm. You will see the message “Timer is On” displaying on the screen. The timer start counting at the time the timer is on.

38 Operation

Image 38
Contents Reference Guide Table of contents Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions ProjectorKeystone buttons Up Remote controlDigital Zoom buttons + FreezeRemote control effective range Replacing the remote control batteryChoosing a location Set Rear Ceiling in the System Setup BasicPositioning your projector Front TableObtaining a preferred projected image size Page Screen diagonal Connection Connecting a computer or monitorConnecting a computer Iii Connecting a monitor Best video quality Connecting Video source devicesConnecting audio Better video qualityConnecting a DVI source device Connection Connecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Sub-menuSecuring the projector Using a security cable lockUtilizing the password function Removing the control keypad on the projectorHighlight Change Security Settings and press Mode/Enter Setting a passwordIf you forget the password Disabling the password function Entering the password recall procedureChanging the password Switching input signal DVI-A DVI-DCreating your own startup screen Changing Color SpaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Page Selecting the aspect ratio About the aspect ratioPC/DVI-A/DVI-D Signal Input Selecting a picture modePicture modes for different types of signals YPbPr/S-Video/Video/HDCP Signal InputUsing Wall Color Setting the User 1/User 2 modeFine-tuning the image quality in user modes About color temperatures Adjusting BrilliantColorSelecting a color temperature 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Presentation Timer menu and press Mode Setting the presentation timerGo to the System Setup Basic Enter to display the Presentation TimerFreezing the image To cancel the timer, perform the following stepsLocking control keys Hiding the image Operating in a high altitude environmentPersonalizing the projector menu display Adjusting the soundAdjusting the sound level Muting the soundShutting down the projector Menu operation Menu systemBasic AdvancedDisplay menu Source menuPicture menu System Setup Basic menu System Setup Advanced menu Status Information menuCurrent System Maintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Tighten the screw that secures the lampIndicators Projector does not turn on TroubleshootingRemote control does not work No pictureSpecifications Projector specificationsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz DimensionsTiming chart Supported timing for PC including DVI-D inputSupported timing for Video and S-Video inputs Signal Format Horizontal Vertical Frequency Frequency kHzSupported timing for Component-YPbPrinput Disclaimer Copyright informationCopyright