InFocus XS1 manual Troubleshooting, Projector does not turn on, No picture, Blurred image

Page 57

Troubleshooting

The projector does not turn on.

Cause

Remedy

 

 

 

Plug the power cord into the AC inlet on the

There is no power from the power

projector, and plug the power cord into the

cable.

power outlet. If the power outlet has a switch,

 

make sure that it is switched on.

 

 

Attempting to turn the projector on

Wait until the cooling down process has

again during the cooling process.

completed.

 

 

No picture

 

Cause

Remedy

 

 

The video source is not turned on or

Turn the video source on and check that the

connected correctly.

signal cable is connected correctly.

 

 

The projector is not correctly

Check the connection.

connected to the input source device.

 

 

 

The input signal has not been

Select the correct input signal with the

SOURCE key on the projector or remote

correctly selected.

control.

 

 

 

The lens cover is still closed.

Open the lens cover.

Blurred image

 

Cause

 

Remedy

 

 

 

The projection lens is not correctly

 

Adjust the focus of the lens using the focus

focused.

 

ring.

 

 

 

The projector and the screen are not

 

Adjust the projection angle and direction as

aligned properly.

 

well as the height of the unit if necessary.

 

 

 

The lens cover is still closed.

 

Open the lens cover.

Remote control does not work

 

Cause

Remedy

 

 

The batteries are out of power.

Replace the batteries with new ones.

There is an obstacle between the

Remove the obstacle.

remote control and the projector.

 

 

 

You are too far away from the

Stand within 8 meters (26 feet) of the

projector.

projector.

 

 

The password is incorrect

 

 

 

Cause

Remedy

 

 

You do not remember the password.

Please see "Entering the password recall pro-

cedure" on page 26 for details.

 

Troubleshooting 57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Reference Guide Table of contents Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsDigital Zoom buttons + Remote controlKeystone buttons Up FreezeReplacing the remote control battery Remote control effective rangePositioning your projector Set Rear Ceiling in the System Setup BasicChoosing a location Front TableObtaining a preferred projected image size Page Screen diagonal Connecting a computer or monitor Connecting a computerConnection Iii Connecting a monitor Connecting audio Connecting Video source devicesBest video quality Better video qualityConnecting a DVI source device Connection To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationSub-menu Using the menusUtilizing the password function Using a security cable lockSecuring the projector Removing the control keypad on the projectorSetting a password If you forget the passwordHighlight Change Security Settings and press Mode/Enter Entering the password recall procedure Changing the passwordDisabling the password function DVI-A DVI-D Switching input signalChanging Color Space Creating your own startup screenAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Page About the aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC/DVI-A/DVI-D Signal Input YPbPr/S-Video/Video/HDCP Signal InputSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Selecting a color temperature Adjusting BrilliantColorAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Go to the System Setup Basic Setting the presentation timerPresentation Timer menu and press Mode Enter to display the Presentation TimerTo cancel the timer, perform the following steps Locking control keysFreezing the image Operating in a high altitude environment Hiding the imageAdjusting the sound level Adjusting the soundPersonalizing the projector menu display Muting the soundShutting down the projector Menu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Current SystemStatus Care of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screw that secures the lamp Resetting the lamp timerIndicators Remote control does not work TroubleshootingProjector does not turn on No pictureProjector specifications SpecificationsTiming chart DimensionsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC including DVI-D inputSignal Format Horizontal Vertical Frequency Frequency kHz Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Copyright information CopyrightDisclaimer
Top Page Image Contents