InFocus XS1 manual Entering the password recall procedure, Changing the password

Page 26

Entering the password recall procedure

Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact InFocus

Customer Center.

Recall Code:

0 2 1 2

MENU Exit

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings > Change Password menu.

2.Press Mode/Enter. The message 'INPUT CURRENT PASSWORD' displays.

3.Enter the old password.

i.If the password is correct, another message 'INPUT NEW PASSWORD' displays.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT CURRENT PASSWORD' displays for your retry. You can press Menu/Exit to cancel the change or try another password.

4.Enter a new password.

The digits being input will display as asterisks on-screen. Write your selected password down here in this reference guide in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this reference guide in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press Menu/Exit.

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system. Press Mode/Enter. The message 'INPUT PASSWORD' displays. Enter the current password.

i.If the password is correct, the OSD menu returns to the Security Settings page.

Press to highlight Power On Lock and press / to select Off. You will not have to enter the password next time when turning on the projector.

Press to highlight Splash Screen Lock and press / to select Off. The Splash Screen function in the SYSTEM SETUP: Basic menu will be available for your change.

26 Operation

Image 26
Contents Reference Guide Table of contents Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions ProjectorKeystone buttons Up Remote controlDigital Zoom buttons + FreezeRemote control effective range Replacing the remote control batteryChoosing a location Set Rear Ceiling in the System Setup BasicPositioning your projector Front TableObtaining a preferred projected image size Page Screen diagonal Connection Connecting a computer or monitorConnecting a computer Iii Connecting a monitor Best video quality Connecting Video source devicesConnecting audio Better video qualityConnecting a DVI source device Connection Connecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Sub-menuSecuring the projector Using a security cable lockUtilizing the password function Removing the control keypad on the projectorHighlight Change Security Settings and press Mode/Enter Setting a passwordIf you forget the password Disabling the password function Entering the password recall procedureChanging the password Switching input signal DVI-A DVI-DCreating your own startup screen Changing Color SpaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Page Selecting the aspect ratio About the aspect ratioPC/DVI-A/DVI-D Signal Input Selecting a picture modePicture modes for different types of signals YPbPr/S-Video/Video/HDCP Signal InputUsing Wall Color Setting the User 1/User 2 modeFine-tuning the image quality in user modes About color temperatures Adjusting BrilliantColorSelecting a color temperature 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Presentation Timer menu and press Mode Setting the presentation timerGo to the System Setup Basic Enter to display the Presentation TimerFreezing the image To cancel the timer, perform the following stepsLocking control keys Hiding the image Operating in a high altitude environmentPersonalizing the projector menu display Adjusting the soundAdjusting the sound level Muting the soundShutting down the projector Menu operation Menu systemBasic AdvancedDisplay menu Source menuPicture menu System Setup Basic menu System Setup Advanced menu Status Information menuCurrent System Maintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Tighten the screw that secures the lampIndicators Projector does not turn on TroubleshootingRemote control does not work No pictureSpecifications Projector specificationsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz DimensionsTiming chart Supported timing for PC including DVI-D inputSupported timing for Video and S-Video inputs Signal Format Horizontal Vertical Frequency Frequency kHzSupported timing for Component-YPbPrinput Disclaimer Copyright informationCopyright