InFocus XS1 manual Remote control effective range, Replacing the remote control battery

Page 8

Remote control effective range

Infra-Red (IR) remote control sensors are located on the front and the back of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam.

Operating the projector from the front

Operating the projector from the rear

A

 

ppr

 

o

 

x.

 

15

 

°

PUSH

 

 

 

 

 

 

°

 

 

 

 

 

5

 

 

 

 

1

 

 

 

 

.

 

 

 

 

 

x

 

 

 

 

 

o

 

 

 

 

 

r

 

 

 

 

 

p

 

 

 

 

p

 

 

 

 

 

A

 

 

 

 

 

 

Replacing the remote control battery

1.Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

2. Insert the new battery in the holder. Note the positive polarity should face outward.

3. Push the holder into the remote control.

CAUTION

Avoid excessive heat and humidity.

There may be battery damage if the battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the battery manufacturer.

Dispose of the used battery according to the battery manufacturer’s instructions.

Never throw a battery into a fire. There may be danger of an explosion.

If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

8 Introduction

Image 8
Contents Reference Guide Table of contents Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions ProjectorRemote control Digital Zoom buttons +Keystone buttons Up FreezeRemote control effective range Replacing the remote control batterySet Rear Ceiling in the System Setup Basic Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Screen diagonal Connection Connecting a computer or monitorConnecting a computer Iii Connecting a monitor Connecting Video source devices Connecting audioBest video quality Better video qualityConnecting a DVI source device Connection Connecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Sub-menuUsing a security cable lock Utilizing the password functionSecuring the projector Removing the control keypad on the projectorHighlight Change Security Settings and press Mode/Enter Setting a passwordIf you forget the password Disabling the password function Entering the password recall procedureChanging the password Switching input signal DVI-A DVI-DCreating your own startup screen Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Page Selecting the aspect ratio About the aspect ratioSelecting a picture mode Picture modes for different types of signalsPC/DVI-A/DVI-D Signal Input YPbPr/S-Video/Video/HDCP Signal InputUsing Wall Color Setting the User 1/User 2 modeFine-tuning the image quality in user modes Adjusting BrilliantColor Selecting a color temperatureAbout color temperatures 3D Color ManagementPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Go to the System Setup BasicPresentation Timer menu and press Mode Enter to display the Presentation TimerFreezing the image To cancel the timer, perform the following stepsLocking control keys Hiding the image Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelPersonalizing the projector menu display Muting the soundShutting down the projector Menu operation Menu systemBasic AdvancedDisplay menu Source menuPicture menu System Setup Basic menu System Setup Advanced menu Status Information menuCurrent System Maintenance Care of the projectorSetting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Tighten the screw that secures the lampIndicators Troubleshooting Remote control does not workProjector does not turn on No pictureSpecifications Projector specificationsDimensions Timing chartHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC including DVI-D inputSupported timing for Video and S-Video inputs Signal Format Horizontal Vertical Frequency Frequency kHzSupported timing for Component-YPbPrinput Disclaimer Copyright informationCopyright