Runco VX-6C, VX-4C manual Throw Distances Placement Section, 720p, 960p, 1024p, Aspect ratio

Page 14

INSTALLATION AND SETUP

2.5Throw Distances - Placement Section

Projector

 

 

Optical

Screen

VX-4c/VX-6c

Throw Distance

Resolution

Aspect Ratio

 

 

 

 

 

720p

Lens 1:

0.8

720p

1.78:1 or 1.33:1

 

Lens 2:

2.2 - 4.0

 

 

 

Lens 3:

4.0 - 7.0

 

 

 

 

 

 

960p

Lens 1: 1.65 - 3.0

960p

1.78:1

 

Lens 2: 3.0 - 5.25

 

 

 

 

 

 

1024p

Lens 1: 1.55 - 2.80

1024p

1.78:1

 

Lens 2: 2.80 - 4.90

 

 

 

 

 

 

1024p

Lens 1: 1.15 - 2.10

1024p

2.35:1

w/ 2.35 aspect ratio

Lens 2: 2.10 - 3.65

w/ 2.35 aspect ratio

 

 

 

 

 

 

The VX-4c/VX-6c 720P system offers high definition resolution in a 16:9 format, while providing multiple aspect ratio selection. Without the use of an anamorphic system.

The VX-4c/VX-6c 960P system provides a 26% increase in brightness and resolution over the base 720P con- figuration. (Using a 1.33 x Anamorphic lens)

The VX-4c/VX-6c 1024P system yields digital cinema resolution by employing every available pixel for a max- imum picture clarity and brightness. (Using a 1.42 x Anamorphic lens)

The VX-4c/VX-6c 1024P/2.35:1 system also makes the maximum resolution fully available, on a 2.35:1 aspect ratio screen. All other common aspect ratios are selectable using the constant height approach. This system was created for the true cinemaphile owning a theater with a cinemascope screen. (Using a 1.90 x Anamorphic lens)

2-7

Image 14
Contents VX-4c and VX-6c Page Table of Contents Page Introduction How The Projector Works?Introduction Components Purchase Record and ServicingPosition the Projector Quick SetupConnect the Line Cord to AC Power Connect a SourceUnplug the projector Installing The LensInstall the lens cap Loosen 3 screwsRotate Slightly Align zoom gear ring to access 3 screwsRotate the lens barrel slightly Install new lens assembly Pull lens assembly outRemove Lens Assembly OrientationMotorized Lens Adjustments Adjust ImageAdjust Image Motorized Models Additional Considerations Installation ConsiderationsLifting 960p Throw Distances Placement Section720p 1024pCalculating Throw Distance Vertical & Horizontal Position Maximum Vertical Offsets Fixed LensesMaximum Vertical Offsets Zoom Lenses Special Mounting Maximum Horizontal Offset ALL LensesMounting Horizontal and Vertical Tilt RangesSource Connections Rear Connector PanelFolded Optics RGB Signals Connecting RGB InputKeypad Protocols and Conversion Independent Keypads and ProjectorsOpening the Keypad Remote Keypad Protocol IR or Wired KeypadStep Set the JumpersLocating and Setting the Jumpers Shortcut Method Converting a KeypadISF 3C Calibration Andy SiedschlagInformation Overview Projector BasicsOperation Reading the Status LEDsPower ON/OFF Wired Remote OptionalKeypad Commands IR RemoteInput Memory BankExit Arrow KeysTint VolumeColor DetailMute PositionShutter Optional Function KeyTest OSD On-screen displayHelp Cinema Menu Navigating the MenusRunco Digital Home On-line HelpTime-outs Accessing General Help TopicsUsing Slidebars and Other Controls To save or To cancel. When you are done, press Entering Text Example of Pull-Down ListEditing Text Selecting an Input Using Inputs and Memory BanksEditing Numerical Values Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Deleting a Memory Bank Copying or Deleting Memory BanksCopying a Memory Bank Editing a Memory BanksOperation Scaling Parameters Adjusting the ImageLoad Default Scaling Parameters MenuFine V Dots Short CUT Press Shift Short CUT Press Image AdjustmentsImage Adjustments Menu Blanking Top, Bottom, Left or RightBrightness Short CUT Press Signal TypeContrast Short CUT Press SharpnessGamma Curve Color BalanceSet Color Balance Gamma Curve Selected Gamma CurvesOSD Settings Menu Display M. Bank List Show Adjust BarIR and Serial Setup Menu Show MessageWired Keypad Front IR Receiver / Back IR ReceiverTest Patterns Test Pattern MenuSubmenu for Menu Options Video TerminationMenu Options Installation Menu DMD Enable Test PatternsDMD Odd Pixel Menu Advanced Color TemperatureDMD Odd Pixel Operational Parameters Menu Color Balance Setup Color Balance Setup MenuPresets and FactoryPresets Set Color BalanceLamp Adjust Lamp Adjust submenuOperation Lamp Adjust Recording the New Lamp Serial NumberInvalid User Entry Error ConditionsInput Signal Error System Warnings / Errors No SignalOther Signal Error Messages Bad SyncSystem Errors Status LED CodesSystem Error Codes Maintenance Projector LocationLamp and Filter Replacement Use only lamps supplied by RuncoServicing CleaningVentilation LensReplacing Keypad Batteries CaseReplacing Keypad Batteries How Old is The Lamp?Troubleshooting Cause / RemedySymptom The display is faint Symptom The power is on but the lamp is notSymptom The display is jittery or unstable Symptom The display is not sharp or clean… Symptom The display is reversed and/or upside-down…Symptom The display appears compressed or stretched… Symptom The display is noisy… Symptom Colors in the display are inaccurate…Symptom The display is not rectangular… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking BlankingAspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications RS-232 Commands Parameter min/max Value stored?Command VHD Ultra Specifications Analog Video Active Line TimeAmbient Light Rejection Aspect RatioCheckbox Color TemperatureDisplay Setting Color ShiftHorizontal Frequency Input SignalHelp Screen Horizontal OffsetResolution projector Pixel PhaseResolution lens MenuRS-232 Source SetupRGB Video RS-422Vertical Offset Throw DistanceVariable Scan Video DecoderKeypad Reference Menu Tree Appendix C Page RUMA-010450