Runco VX-4C, VX-6C manual Components, Purchase Record and Servicing

Page 7

INTRODUCTION

1.3Components

Included with the VX-4c/VX-6c is an infrared (IR) remote keypad, high-current 13 amp rated line cord, a 9/64” hex socket ball driver, and a VX-4c/VX-6c owner’s manual. Make sure that you have all these items, and note that if you have purchased this projector, a purchaser’s Warranty Registration Card is also included. Complete this card and return it directly to Runco International as soon as possible.

Owner's Operating Manual

TWO YEAR LIMITED WARRANTY

1.4Purchase Record and Servicing

Whether the projector is under warranty or the warranty has expired, Runco’s extensive factory and dealer service network is always available. Runco service technicians and dealers are fully trained to quickly diagnose and correct projector malfunctions.

Should you encounter a problem with the projector and require assistance, contact your Runco dealer or Runco International. In many cases, any necessary servicing can be performed on site. If you have purchased the projector, fill out the information below and keep with your records.

Purchase Record

Dealer:

Dealer Phone Number:

Projector Serial Number*:

Purchase Date:

Installation Date, if applicable:

* NOTE: The projector serial number is located on the projector's rear identification label

1-3

Image 7
Contents VX-4c and VX-6c Page Table of Contents Page How The Projector Works? IntroductionIntroduction Purchase Record and Servicing ComponentsConnect a Source Quick SetupConnect the Line Cord to AC Power Position the ProjectorLoosen 3 screws Installing The LensInstall the lens cap Unplug the projectorRotate the lens barrel slightly Align zoom gear ring to access 3 screwsRotate Slightly Orientation Pull lens assembly outRemove Lens Assembly Install new lens assemblyAdjust Image Motorized Models Adjust ImageMotorized Lens Adjustments Lifting Installation ConsiderationsAdditional Considerations 1024p Throw Distances Placement Section720p 960pCalculating Throw Distance Maximum Vertical Offsets Fixed Lenses Vertical & Horizontal PositionMaximum Vertical Offsets Zoom Lenses Horizontal and Vertical Tilt Ranges Maximum Horizontal Offset ALL LensesMounting Special MountingFolded Optics Rear Connector PanelSource Connections Connecting RGB Input RGB SignalsIndependent Keypads and Projectors Keypad Protocols and ConversionSet the Jumpers Remote Keypad Protocol IR or Wired KeypadStep Opening the KeypadLocating and Setting the Jumpers Converting a Keypad Shortcut MethodAndy Siedschlag ISF 3C CalibrationInformation Projector Basics OverviewReading the Status LEDs OperationIR Remote Wired Remote OptionalKeypad Commands Power ON/OFFMemory Bank InputArrow Keys ExitDetail VolumeColor TintFunction Key PositionShutter Optional MuteHelp OSD On-screen displayTest On-line Help Navigating the MenusRunco Digital Home Cinema MenuUsing Slidebars and Other Controls Accessing General Help TopicsTime-outs To save or To cancel. When you are done, press Editing Text Example of Pull-Down ListEntering Text Editing Numerical Values Using Inputs and Memory BanksSelecting an Input Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Editing a Memory Banks Copying or Deleting Memory BanksCopying a Memory Bank Deleting a Memory BankOperation Scaling Parameters Menu Adjusting the ImageLoad Default Scaling ParametersFine V Dots Short CUT Press Blanking Top, Bottom, Left or Right Image AdjustmentsImage Adjustments Menu Shift Short CUT PressSharpness Signal TypeContrast Short CUT Press Brightness Short CUT PressSet Color Balance Color BalanceGamma Curve Selected Gamma Curves Gamma CurveOSD Settings Menu Show Message Show Adjust BarIR and Serial Setup Menu Display M. Bank ListFront IR Receiver / Back IR Receiver Wired KeypadTest Pattern Menu Test PatternsMenu Options Video TerminationSubmenu for Menu Options Installation Menu Test Patterns DMD EnableDMD Odd Pixel Advanced Color TemperatureDMD Odd Pixel Menu Operational Parameters Menu Color Balance Setup Menu Color Balance SetupSet Color Balance Presets and FactoryPresetsLamp Adjust submenu Lamp AdjustOperation Recording the New Lamp Serial Number Lamp AdjustInput Signal Error Error ConditionsInvalid User Entry Bad Sync No SignalOther Signal Error Messages System Warnings / ErrorsStatus LED Codes System ErrorsSystem Error Codes Projector Location MaintenanceUse only lamps supplied by Runco Lamp and Filter ReplacementLens CleaningVentilation ServicingHow Old is The Lamp? CaseReplacing Keypad Batteries Replacing Keypad BatteriesCause / Remedy TroubleshootingSymptom The display is jittery or unstable Symptom The power is on but the lamp is notSymptom The display is faint Symptom The display appears compressed or stretched… Symptom The display is reversed and/or upside-down…Symptom The display is not sharp or clean… Symptom The display is not rectangular… Symptom Colors in the display are inaccurate…Symptom The display is noisy… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking BlankingAspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications Parameter min/max Value stored? RS-232 CommandsCommand VHD Ultra Specifications Aspect Ratio Active Line TimeAmbient Light Rejection Analog VideoColor Shift Color TemperatureDisplay Setting CheckboxHorizontal Offset Input SignalHelp Screen Horizontal FrequencyMenu Pixel PhaseResolution lens Resolution projectorRS-422 Source SetupRGB Video RS-232Video Decoder Throw DistanceVariable Scan Vertical OffsetKeypad Reference Menu Tree Appendix C Page RUMA-010450