Runco VX-4C, VX-6C manual Menu Description and Navigation

Page 87

MENU DESCRIPTION AND NAVIGATION

Main Menu

MAIN MENU

>COMPOSITE S-VIDEO COMPONENT PASS THROUGH

ASPECT RATIO INSTALLATION

Source selection and picture quality adjustments

Aspect ratio selection

See "installation" section

When the MENU button is pressed on either the remote control or the front panel, the main menu will appear on-screen. An example of the main menu is shown above.

The active source is indicated by an arrow to the left of the source; note that in the example above, Composite is the current source.

To select a source via the main menu, press either the up or down buttons on the remote or front panel and highlight the desired source, and press ENTER. Otherwise, you may select a source by pressing either the left or right arrow buttons (on the remote or front panel) when no menus are on-screen, or by pressing one of the direct access buttons on the remote control (recommended; see page 6-8).

If pass-through is selected, note that no on-screen menus will be displayed since the signal is simply being 'looped' directly to the output. When pass-through is the selected source, pressing MENU will auto- matically select the last selected input before Pass-through was selected. If you wish to choose another source, Runco recommends using the direct access buttons to select the desired source as opposed to pressing MENU.

Aspect Ratio provides selection of one of three aspect ratios: Anamorphic, Letterbox or standard 4:3. To select an aspect ratio via the main menu, press either the up and down buttons on the remote or front panel, highlight ASPECT RATIO and press ENTER. The aspect ratio menu will then appear with the three choices; highlight the desired aspect ratio with the up or down buttons and press ENTER. Otherwise, you may select an aspect ratio by pressing either the up or down arrow buttons (on the remote or front panel) when no menus are on-screen, or by pressing one of the direct access buttons on the remote control (rec- ommended; see page 6-8).

Installation is where the image shift and blanking controls are located. A full description of this menu is on page 6-13.

NOTE: If INSTALLATION does not appear on the main menu, see page 6-13 for an explanation on how to access the Installation menu.

6-10

Image 87

Contents VX-4c and VX-6c Page Table of Contents Page How The Projector Works? IntroductionIntroduction Purchase Record and Servicing ComponentsConnect a Source Quick SetupConnect the Line Cord to AC Power Position the ProjectorLoosen 3 screws Installing The LensInstall the lens cap Unplug the projectorAlign zoom gear ring to access 3 screws Rotate the lens barrel slightlyRotate Slightly Orientation Pull lens assembly outRemove Lens Assembly Install new lens assemblyAdjust Image Adjust Image Motorized ModelsMotorized Lens Adjustments Installation Considerations LiftingAdditional Considerations 1024p Throw Distances Placement Section720p 960pCalculating Throw Distance Maximum Vertical Offsets Fixed Lenses Vertical & Horizontal PositionMaximum Vertical Offsets Zoom Lenses Horizontal and Vertical Tilt Ranges Maximum Horizontal Offset ALL LensesMounting Special MountingRear Connector Panel Folded OpticsSource Connections Connecting RGB Input RGB SignalsIndependent Keypads and Projectors Keypad Protocols and ConversionSet the Jumpers Remote Keypad Protocol IR or Wired KeypadStep Opening the KeypadLocating and Setting the Jumpers Converting a Keypad Shortcut MethodAndy Siedschlag ISF 3C CalibrationInformation Projector Basics OverviewReading the Status LEDs OperationIR Remote Wired Remote OptionalKeypad Commands Power ON/OFFMemory Bank InputArrow Keys ExitDetail VolumeColor TintFunction Key PositionShutter Optional MuteOSD On-screen display HelpTest On-line Help Navigating the MenusRunco Digital Home Cinema MenuAccessing General Help Topics Using Slidebars and Other ControlsTime-outs To save or To cancel. When you are done, press Example of Pull-Down List Editing TextEntering Text Using Inputs and Memory Banks Editing Numerical ValuesSelecting an Input Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Editing a Memory Banks Copying or Deleting Memory BanksCopying a Memory Bank Deleting a Memory BankOperation Scaling Parameters Menu Adjusting the ImageLoad Default Scaling ParametersFine V Dots Short CUT Press Blanking Top, Bottom, Left or Right Image AdjustmentsImage Adjustments Menu Shift Short CUT PressSharpness Signal TypeContrast Short CUT Press Brightness Short CUT PressColor Balance Set Color BalanceGamma Curve Selected Gamma Curves Gamma CurveOSD Settings Menu Show Message Show Adjust BarIR and Serial Setup Menu Display M. Bank ListFront IR Receiver / Back IR Receiver Wired KeypadTest Pattern Menu Test PatternsVideo Termination Menu OptionsSubmenu for Menu Options Installation Menu Test Patterns DMD EnableAdvanced Color Temperature DMD Odd PixelDMD Odd Pixel Menu Operational Parameters Menu Color Balance Setup Menu Color Balance SetupSet Color Balance Presets and FactoryPresetsLamp Adjust submenu Lamp AdjustOperation Recording the New Lamp Serial Number Lamp AdjustError Conditions Input Signal ErrorInvalid User Entry Bad Sync No SignalOther Signal Error Messages System Warnings / ErrorsStatus LED Codes System ErrorsSystem Error Codes Projector Location MaintenanceUse only lamps supplied by Runco Lamp and Filter ReplacementLens CleaningVentilation ServicingHow Old is The Lamp? CaseReplacing Keypad Batteries Replacing Keypad BatteriesCause / Remedy TroubleshootingSymptom The power is on but the lamp is not Symptom The display is jittery or unstableSymptom The display is faint Symptom The display is reversed and/or upside-down… Symptom The display appears compressed or stretched…Symptom The display is not sharp or clean… Symptom Colors in the display are inaccurate… Symptom The display is not rectangular…Symptom The display is noisy… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking BlankingAspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications Parameter min/max Value stored? RS-232 CommandsCommand VHD Ultra Specifications Aspect Ratio Active Line TimeAmbient Light Rejection Analog VideoColor Shift Color TemperatureDisplay Setting CheckboxHorizontal Offset Input SignalHelp Screen Horizontal FrequencyMenu Pixel PhaseResolution lens Resolution projectorRS-422 Source SetupRGB Video RS-232Video Decoder Throw DistanceVariable Scan Vertical OffsetKeypad Reference Menu Tree Appendix C Page RUMA-010450