Runco VX-6C, VX-4C manual Installation Menu

Page 90

NOTE: Some DVD players cannot pass the 'blacker than black' bar (they won't pass PLUGE), and that bar will never be visible. In a case like this, adjust the 'above black' bar until it is slightly brighter than the background that surrounds it.

SHARPNESS adjusts the amount of high-frequency detail in the image. This can be adjusted to the pref- erence of the user. Keep in mind that when SHARPNESS is decreased, fine details in the image will become 'soft'; when it is increased, fine details will become sharper but will also make the picture appear 'noisy' if adjusted too high.

LUMA ENHANCE acts as an edge enhancement, especially around black to white transitions in the image. Essentially, this has the same characteristics as sharpness but affects the edges of objects far more that the rest of the image.

FREQUENCIES HIGH/LOW affect the overall range of the LUMA ENHANCE feature. For example, if using a lower-quality video source such as a VCR, the FREQUENCIES should be set to LOW. For a good quality source such as a DVD player, set FREQUENCIES to HIGH. To set FREQUENCIES, press ENTER while LUMA ENHANCE is on-screen.

CHROMA ENHANCE acts as an edge enhancement, especially around color transitions in the image. Essentially, this has the same characteristics as sharpness but affects the edges of objects far more that the rest of the image.

Installation Menu

The Installation menu is where you can adjust the type of screen (4:3 or 16:9), shift the image or set blank- ing.

When the VHD Ultra Controller is turned on for the first time, the INSTALLATION item will not appear in the main menu. To enable the INSTALLATION menu, there are two options:

·With the processor ON and no menus on-screen, simultaneously press the ENTER, UP and LEFT buttons (you don't need to hold them down). Release the three buttons and press MENU, ensure INSTAL- LATION is now on the bottom of the main menu.

·With the remote control, press button 6 (with no menus on-screen). After pressing '6', press MENU and ensure INSTALLATION is now on the bottom of the main menu.

After INSTALLATION has been accessed, press MENU, highlight INSTALLATION and press ENTER. This will bring up the INSTALLATION MENU, shown below:

INSTALLATION

4:3 SCREEN > 16:9 SCREEN

IMAGE SHIFT

BLANKING

6-13

Image 90
Contents VX-4c and VX-6c Page Table of Contents Page Introduction How The Projector Works?Introduction Components Purchase Record and ServicingPosition the Projector Quick SetupConnect the Line Cord to AC Power Connect a SourceUnplug the projector Installing The LensInstall the lens cap Loosen 3 screwsAlign zoom gear ring to access 3 screws Rotate the lens barrel slightlyRotate Slightly Install new lens assembly Pull lens assembly outRemove Lens Assembly OrientationAdjust Image Adjust Image Motorized ModelsMotorized Lens Adjustments Installation Considerations LiftingAdditional Considerations 960p Throw Distances Placement Section720p 1024pCalculating Throw Distance Vertical & Horizontal Position Maximum Vertical Offsets Fixed LensesMaximum Vertical Offsets Zoom Lenses Special Mounting Maximum Horizontal Offset ALL LensesMounting Horizontal and Vertical Tilt RangesRear Connector Panel Folded OpticsSource Connections RGB Signals Connecting RGB InputKeypad Protocols and Conversion Independent Keypads and ProjectorsOpening the Keypad Remote Keypad Protocol IR or Wired KeypadStep Set the JumpersLocating and Setting the Jumpers Shortcut Method Converting a KeypadISF 3C Calibration Andy SiedschlagInformation Overview Projector BasicsOperation Reading the Status LEDsPower ON/OFF Wired Remote OptionalKeypad Commands IR RemoteInput Memory BankExit Arrow KeysTint VolumeColor DetailMute PositionShutter Optional Function KeyOSD On-screen display HelpTest Cinema Menu Navigating the MenusRunco Digital Home On-line HelpAccessing General Help Topics Using Slidebars and Other ControlsTime-outs To save or To cancel. When you are done, press Example of Pull-Down List Editing TextEntering Text Using Inputs and Memory Banks Editing Numerical ValuesSelecting an Input Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Deleting a Memory Bank Copying or Deleting Memory BanksCopying a Memory Bank Editing a Memory BanksOperation Scaling Parameters Adjusting the ImageLoad Default Scaling Parameters MenuFine V Dots Short CUT Press Shift Short CUT Press Image AdjustmentsImage Adjustments Menu Blanking Top, Bottom, Left or RightBrightness Short CUT Press Signal TypeContrast Short CUT Press SharpnessColor Balance Set Color BalanceGamma Curve Gamma Curve Selected Gamma CurvesOSD Settings Menu Display M. Bank List Show Adjust BarIR and Serial Setup Menu Show MessageWired Keypad Front IR Receiver / Back IR ReceiverTest Patterns Test Pattern MenuVideo Termination Menu OptionsSubmenu for Menu Options Installation Menu DMD Enable Test PatternsAdvanced Color Temperature DMD Odd PixelDMD Odd Pixel Menu Operational Parameters Menu Color Balance Setup Color Balance Setup MenuPresets and FactoryPresets Set Color BalanceLamp Adjust Lamp Adjust submenuOperation Lamp Adjust Recording the New Lamp Serial NumberError Conditions Input Signal ErrorInvalid User Entry System Warnings / Errors No SignalOther Signal Error Messages Bad SyncSystem Errors Status LED CodesSystem Error Codes Maintenance Projector LocationLamp and Filter Replacement Use only lamps supplied by RuncoServicing CleaningVentilation LensReplacing Keypad Batteries CaseReplacing Keypad Batteries How Old is The Lamp?Troubleshooting Cause / RemedySymptom The power is on but the lamp is not Symptom The display is jittery or unstableSymptom The display is faint Symptom The display is reversed and/or upside-down… Symptom The display appears compressed or stretched…Symptom The display is not sharp or clean… Symptom Colors in the display are inaccurate… Symptom The display is not rectangular…Symptom The display is noisy… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking BlankingAspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications RS-232 Commands Parameter min/max Value stored?Command VHD Ultra Specifications Analog Video Active Line TimeAmbient Light Rejection Aspect RatioCheckbox Color TemperatureDisplay Setting Color ShiftHorizontal Frequency Input SignalHelp Screen Horizontal OffsetResolution projector Pixel PhaseResolution lens MenuRS-232 Source SetupRGB Video RS-422Vertical Offset Throw DistanceVariable Scan Video DecoderKeypad Reference Menu Tree Appendix C Page RUMA-010450