Runco VX-6C, VX-4C manual Video Termination, Submenu for Menu Options

Page 54

OPERATION

Video Termination

Enter a checkmark to terminate the video inputs 3 and 4 (75W). The input should be terminated unless the signal loops through (continues) to another projector or display device, in which case only the last projector in the chain should be terminated.

*For all single free-standing projectors

*For last projector in a network

*For all networked projectors except the last one

Menu Options

In this submenu, choose the default location desired for on-screen menus. You can use the shift options to move a location up or down, creating a Custom location. Note that menus for this pro- jector often expand and can be quite large - avoid placing them too low or too far to the right where they may be cropped.

Variable

4:3 Upper/Left

4:3 In 1

4:3 In 2

16:9 Upper/Left

16:9 In 1

16:9 In 2

Variable

Submenu for Menu Options

3-28

Image 54

Contents VX-4c and VX-6c Page Table of Contents Page Introduction How The Projector Works?Introduction Components Purchase Record and ServicingPosition the Projector Quick SetupConnect the Line Cord to AC Power Connect a SourceUnplug the projector Installing The LensInstall the lens cap Loosen 3 screwsAlign zoom gear ring to access 3 screws Rotate the lens barrel slightlyRotate Slightly Install new lens assembly Pull lens assembly outRemove Lens Assembly OrientationAdjust Image Adjust Image Motorized ModelsMotorized Lens Adjustments Installation Considerations LiftingAdditional Considerations 960p Throw Distances Placement Section720p 1024pCalculating Throw Distance Vertical & Horizontal Position Maximum Vertical Offsets Fixed LensesMaximum Vertical Offsets Zoom Lenses Special Mounting Maximum Horizontal Offset ALL LensesMounting Horizontal and Vertical Tilt RangesRear Connector Panel Folded OpticsSource Connections RGB Signals Connecting RGB InputKeypad Protocols and Conversion Independent Keypads and ProjectorsOpening the Keypad Remote Keypad Protocol IR or Wired KeypadStep Set the JumpersLocating and Setting the Jumpers Shortcut Method Converting a KeypadISF 3C Calibration Andy SiedschlagInformation Overview Projector BasicsOperation Reading the Status LEDsPower ON/OFF Wired Remote OptionalKeypad Commands IR RemoteInput Memory BankExit Arrow KeysTint VolumeColor DetailMute PositionShutter Optional Function KeyOSD On-screen display HelpTest Cinema Menu Navigating the MenusRunco Digital Home On-line HelpAccessing General Help Topics Using Slidebars and Other ControlsTime-outs To save or To cancel. When you are done, press Example of Pull-Down List Editing TextEntering Text Using Inputs and Memory Banks Editing Numerical ValuesSelecting an Input Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Deleting a Memory Bank Copying or Deleting Memory BanksCopying a Memory Bank Editing a Memory BanksOperation Scaling Parameters Adjusting the ImageLoad Default Scaling Parameters MenuFine V Dots Short CUT Press Shift Short CUT Press Image AdjustmentsImage Adjustments Menu Blanking Top, Bottom, Left or RightBrightness Short CUT Press Signal TypeContrast Short CUT Press SharpnessColor Balance Set Color BalanceGamma Curve Gamma Curve Selected Gamma CurvesOSD Settings Menu Display M. Bank List Show Adjust BarIR and Serial Setup Menu Show MessageWired Keypad Front IR Receiver / Back IR ReceiverTest Patterns Test Pattern MenuVideo Termination Menu OptionsSubmenu for Menu Options Installation Menu DMD Enable Test PatternsAdvanced Color Temperature DMD Odd PixelDMD Odd Pixel Menu Operational Parameters Menu Color Balance Setup Color Balance Setup MenuPresets and FactoryPresets Set Color BalanceLamp Adjust Lamp Adjust submenuOperation Lamp Adjust Recording the New Lamp Serial NumberError Conditions Input Signal ErrorInvalid User Entry System Warnings / Errors No SignalOther Signal Error Messages Bad SyncSystem Errors Status LED CodesSystem Error Codes Maintenance Projector LocationLamp and Filter Replacement Use only lamps supplied by RuncoServicing CleaningVentilation LensReplacing Keypad Batteries CaseReplacing Keypad Batteries How Old is The Lamp?Troubleshooting Cause / RemedySymptom The power is on but the lamp is not Symptom The display is jittery or unstableSymptom The display is faint Symptom The display is reversed and/or upside-down… Symptom The display appears compressed or stretched…Symptom The display is not sharp or clean… Symptom Colors in the display are inaccurate… Symptom The display is not rectangular…Symptom The display is noisy… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking BlankingAspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications RS-232 Commands Parameter min/max Value stored?Command VHD Ultra Specifications Analog Video Active Line TimeAmbient Light Rejection Aspect RatioCheckbox Color TemperatureDisplay Setting Color ShiftHorizontal Frequency Input SignalHelp Screen Horizontal OffsetResolution projector Pixel PhaseResolution lens MenuRS-232 Source SetupRGB Video RS-422Vertical Offset Throw DistanceVariable Scan Video DecoderKeypad Reference Menu Tree Appendix C Page RUMA-010450