Runco VX-4C, VX-6C manual VHD Ultra Specifications

Page 99

VHD ULTRA SPECIFICATIONS

Aspect Ratios:

Anamorphic, Letterbox, 4:3 (on either 16:9 or 4:3 screens)

Input Standards:

NTSC, PAL

Outputs:

Native Resolution: 720P, 960P, 1024P and 1024P Anamorphic

 

HD Pass-Through: Up to 1080P

Inputs:

(1) Composite, (1) S-Video, (1) Component, (1) Pass-through

Control Options:

Infrared (with discrete on/off, aspect ratio and source selection), RS-232 and

 

Front Panel

Screen Trigger/

 

Masking Outputs:

(2) 12V DC, 1/8A

Bandwidth:

Video Inputs: 5.5 Mhz, PAss-Through: 100 Mhz

Power Requirements:

100-240V AC (auto sensing), 50/60 Hz, 15W

Operating Environment:

41°-95°F (5°-35° C), 0-90% Humidity, (non-condensing)

Dimensions:

Width: 17 1/2 in. (444.50 mm)

(w/out feet)

Depth: 16 in. (406.40 mm)

 

Height: 3 1/2 in. (88.90 mm)

 

Weight: 16 lbs. (7.3 kg)

Included Accessories:

Rack mounting brackets

Regulatory Approvals:

Complies with FCC Class 'B', CE, C-tick

Limited Warranty:

(2) Two years parts and labor from the date of delivery to the end user.

6-22

Page 98 Page 100
Image 99
Page 98 Page 100
Contents VX-4c and VX-6c Page Table of Contents Page How The Projector Works? IntroductionIntroduction Purchase Record and Servicing ComponentsConnect a Source Quick SetupConnect the Line Cord to AC Power Position the ProjectorLoosen 3 screws Installing The LensInstall the lens cap Unplug the projectorAlign zoom gear ring to access 3 screws Rotate the lens barrel slightlyRotate Slightly Orientation Pull lens assembly outRemove Lens Assembly Install new lens assemblyAdjust Image Adjust Image Motorized ModelsMotorized Lens Adjustments Installation Considerations LiftingAdditional Considerations 1024p Throw Distances Placement Section720p 960pCalculating Throw Distance Maximum Vertical Offsets Fixed Lenses Vertical & Horizontal PositionMaximum Vertical Offsets Zoom Lenses Horizontal and Vertical Tilt Ranges Maximum Horizontal Offset ALL LensesMounting Special MountingRear Connector Panel Folded OpticsSource Connections Connecting RGB Input RGB SignalsIndependent Keypads and Projectors Keypad Protocols and ConversionSet the Jumpers Remote Keypad Protocol IR or Wired KeypadStep Opening the KeypadLocating and Setting the Jumpers Converting a Keypad Shortcut MethodAndy Siedschlag ISF 3C CalibrationInformation Projector Basics OverviewReading the Status LEDs OperationIR Remote Wired Remote OptionalKeypad Commands Power ON/OFFMemory Bank InputArrow Keys ExitDetail VolumeColor TintFunction Key PositionShutter Optional MuteOSD On-screen display HelpTest On-line Help Navigating the MenusRunco Digital Home Cinema MenuAccessing General Help Topics Using Slidebars and Other ControlsTime-outs To save or To cancel. When you are done, press Example of Pull-Down List Editing TextEntering Text Using Inputs and Memory Banks Editing Numerical ValuesSelecting an Input Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Editing a Memory Banks Copying or Deleting Memory BanksCopying a Memory Bank Deleting a Memory BankOperation Scaling Parameters Menu Adjusting the ImageLoad Default Scaling ParametersFine V Dots Short CUT Press Blanking Top, Bottom, Left or Right Image AdjustmentsImage Adjustments Menu Shift Short CUT PressSharpness Signal TypeContrast Short CUT Press Brightness Short CUT PressColor Balance Set Color BalanceGamma Curve Selected Gamma Curves Gamma CurveOSD Settings Menu Show Message Show Adjust BarIR and Serial Setup Menu Display M. Bank ListFront IR Receiver / Back IR Receiver Wired KeypadTest Pattern Menu Test PatternsVideo Termination Menu OptionsSubmenu for Menu Options Installation Menu Test Patterns DMD EnableAdvanced Color Temperature DMD Odd PixelDMD Odd Pixel Menu Operational Parameters Menu Color Balance Setup Menu Color Balance SetupSet Color Balance Presets and FactoryPresetsLamp Adjust submenu Lamp AdjustOperation Recording the New Lamp Serial Number Lamp AdjustError Conditions Input Signal ErrorInvalid User Entry Bad Sync No SignalOther Signal Error Messages System Warnings / ErrorsStatus LED Codes System ErrorsSystem Error Codes Projector Location MaintenanceUse only lamps supplied by Runco Lamp and Filter ReplacementLens CleaningVentilation ServicingHow Old is The Lamp? CaseReplacing Keypad Batteries Replacing Keypad BatteriesCause / Remedy TroubleshootingSymptom The power is on but the lamp is not Symptom The display is jittery or unstableSymptom The display is faint Symptom The display is reversed and/or upside-down… Symptom The display appears compressed or stretched…Symptom The display is not sharp or clean… Symptom Colors in the display are inaccurate… Symptom The display is not rectangular…Symptom The display is noisy… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking BlankingAspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications Parameter min/max Value stored? RS-232 CommandsCommand VHD Ultra Specifications Aspect Ratio Active Line TimeAmbient Light Rejection Analog VideoColor Shift Color TemperatureDisplay Setting CheckboxHorizontal Offset Input SignalHelp Screen Horizontal FrequencyMenu Pixel PhaseResolution lens Resolution projectorRS-422 Source SetupRGB Video RS-232Video Decoder Throw DistanceVariable Scan Vertical OffsetKeypad Reference Menu Tree Appendix C Page RUMA-010450
Top Page Image Contents