Sharp AL-1644, AL-1633 operation manual Installing the TD Cartridge, Close the front cover

Page 16

INSTALLING THE TD CARTRIDGE

1 Push gently on both ends of the front cover and open it.

4 Insert the TD cartridge along the guides until it locks in place.

If there is any dirt or dust on the TD cartridge, remove it before installing the cartridge.

2 Remove the new TD cartridge from the bag. Hold the cartridge on both sides and shake it horizontally four or five times.

4 or 5 times

5 Close the front cover.

The TD cartridge replacement required indicator () will go out.

• Before closing the front cover, make sure

Note that the TD cartridge is correctly installed.

• When closing the front cover, gently hold both ends.

3 Remove the protective cover from the TD cartridge by unlatching three cover hooks from the holes on the cartridge and then pulling the cover in the direction indicated by the arrow in the illustration.

Image 16

Contents AL-1633 AL-1644Page Contents Troubleshooting Misfeed in the SPF only on the SPF modelImportant Points When Selecting AN Installation Site Do not install your machine in areas that areChanges, e.g., near an Air conditioner orTrademark acknowledgements Using the Manual Online Manual on the accessory CD-ROMSoftware Setup Guide separate manual Environmental InformationConventions Used in this Manual SPF Differences Between ModelsThis manual covers the following models Model AL-1644 AL-1633 AppearanceMain Features Part Names and Functions Fusing unit release levers Fusing unit paper guide Open to remove misfed paperParallel port Document feeder trayOperation Panel Original Size Enter key Enter / Original Size indicators Paper Size indicatorsSPF indicator only on the SPF model Auto Image key Auto % / indicatorChecking Packed Components and Accessories UnpackingInstall the TD cartridge For installation of the TD cartridge, see the nextSET-UP Gently lift and pull out the paper tray until it stopsTD cartridge replacement required indicator will go out Installing the TD CartridgeClose the front cover Power on and OFF Power onPower OFF Power Save ModesPaper tray type Paper type Size Weight Capacity Loading PaperPaper Special papersLoading Paper Loading the paper trayLocks in place Fan the paperImportant points when inserting paper in the bypass tray Loading the bypass trayUnfold the bypass tray Set the paper guides to the copy paper widthChanging a TRAY’S Paper Size Setting EnvelopesImportant points when using the printer mode Press the Start key and then press the Paper Size Enter keyCopying from the document glass Normal CopyingOpen the document cover/SPF, and place the original Set the originals face up in the document feeder tray Copying from the SPF only on the SPF modelSet the number of copies Auto paper select mode Two-tray model only Auto tray switching Two-tray model only Making a Copy Darker or LighterSelecting the Tray Original typesSetting the Number of Copies REDUCTION/ENLAREGMENT/ZOOMAutomatic Ratio Selection Original position Selectable ratiosSelecting a preset ratio Fine adjustment of the ratioManual Ratio Selection Press the Auto Image key Auto %XY Zoom copying Press the Copy ratio display keyDown the Copy ratio display key Copy original a TWO-SIDED Copying Using the Bypass TrayPlace original B as shown below Dual page Copying Press the Interrupt key to interrupt the copy run Interrupting a Copy RUNReplace the previous originals and press the Start key Using the Printer Mode Basic Procedure for PrintingMake sure that paper is loaded in the tray Click the Print button or the OK button to begin printingUsing the Scanner Mode Scanning Using the Keys on the MachinePausing a print job When Use close paper size is disabledScanning from Your Computer Scan Menu keys and the Button Manager scan menuPress a Scan Menu key to begin ScanningOperation in COPY, PRINTER, and Scanner Modes During copyingPrinter During printing Scanner During scan previewAdjusting the Automatic Exposure Level Enabling Toner Save Mode When enabling tonerPhoto indicator stops blinking and lights steadily Save mode, make sureCustomising Settings User ProgramsExplanation 300dpiMinimum Short beepSelecting a Setting for a User Program Base settingsSettings for Auditing Mode Auditing ModeAuditing Mode Settings Factory default settingsSelecting Auditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.41Auditing mode Account number entryAccount number change Account number deletionResetting account Copying when Auditing mode is enabledTroubleshooting MACHINE/COPYING Problems Problem Cause and solution Misfeed occurs Paper is not loaded properlyPieces of paper inside machine Paper misfeed Too much paper is loaded in the trayAny other indicators are lit Power Save indicator isPower Save indicator is only lit Lit Original smudged or blotchyPrinting and Scanning Problems Printed image is dirty UnevenRuns off the paper You have not specified a suitable resolution Brightness and contrast settings are not suitableOriginal is smudged or blotchy Poor scanning qualityRemoving the software Click the start button, and then click Control PanelClick Add or Remove Programs If you need to remove the software, follow these stepsIndicators and Display Messages Remove the misfed original Misfeed RemovalAL-1644 AL-1633 Misfeed indicator will go out Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the paper feed areaAllow easier removal Misfeed in the fusing areaMisfed paper during Close the side cover Misfeed in the transport areaBe careful not to tear the misfed paper during removal Close the upper paper tray Misfeed in the Upper Paper TrayPush the upper paper tray in completely Open the lower side cover Close the lower paper tray Remove the misfed paperClose the lower side cover Grasp the handle to open the lower side coverReplacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Checking the Total Output Count Checking the Total Output CountTotal output count Total copy countChecking the Toner Level and Drum Cartridge Life Toner LevelPress the Light key to return to the normal display Hold down the Clear key for more than 5 secondsCleaning the Document Glass and SPF/ Document Cover Routine MaintenanceCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Storage of Supplies Supply Part NumbersProper Storage Supply listWhen moving this machine, follow the procedure below Accessories p.12Moving Instructions Specifications SPF only on the SPF model Specifications Printer FunctionScanner Function Software License Page Symbols IndexTD cartridge replacement required Tray Select key 11, 19, 21, 23 TroubleshootingPrinting and scanning problems Normal copyingProblem occurs Machine settingsIndicators, lit and blinking Memo Memo Class Laser Product Laser Klasse Page 2004E