Sharp AL-1644 Loading Paper, Special papers, Paper tray type Paper type Size Weight Capacity

Page 18

LOADING PAPER

The paper required indicator ( ) will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed.

PAPER

For best results, use only SHARP recommended paper.

Paper tray type	Paper type	Size		Weight	Capacity
Paper tray	Standard paper	A5*1		56 g/m2 to 90 g/m2 *2	250 sheets
	Recycled paper	A4			(Load paper lower
		B4			than the line on the
		A3			tray)

Bypass tray	Standard paper	A6R to A3		56 g/m2 to 80 g/m2	100 sheets *3
	Recycled paper

	Thick paper			Max. 200 g/m2	Load one sheet of
					these papers at a
	Transparency film				these papers at a
	Transparency film				time to the bypass
	Labels				time to the bypass
	Labels				tray.
					tray.

	Envelopes	International DL			5 sheets
		(110 mm x 220 mm)
		International C5
		(162 mm x 229 mm)
		Commercial 9
		(3-7/8" x 8-7/8")
		Commercial 10
		(4-1/2" x 9-1/2")

*1 A5 can be used in the upper paper tray but cannot be used in other trays (including trays in optional paper feeding unit). *2 When making a large number of copies or prints using 90 g/m2 paper, remove the output from the paper output tray when

about 100 pages have been printed. The output may not stack correctly if more than 100 pages are allowed to accumulate. *3 The number of sheets of the paper which can be set changes with the weight of a paper.

Special papers

Follow these guidelines when using special papers.

●Use SHARP recommended transparency film and label sheets. Using other than SHARP recommended paper may result in misfeeds or smudges on the output. If other than SHARP recommended media must be used, feed each sheet one at a time using the bypass tray (do not attempt continuous copying or printing).

●There are many varieties of special paper available on the market, and some cannot be used with this machine. Before using special paper, contact your authorised service representative.

●Before using other than SHARP recommended paper, make a test copy to see if the paper is suitable.

16

Image 18

Contents AL-1633 AL-1644Page Contents Troubleshooting Misfeed in the SPF only on the SPF modelChanges, e.g., near an Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Air conditioner orTrademark acknowledgements Software Setup Guide separate manual Using the ManualOnline Manual on the accessory CD-ROM Environmental InformationThis manual covers the following models Conventions Used in this ManualSPF Differences Between Models Model AL-1644 AL-1633 AppearanceMain Features Part Names and Functions Parallel port Fusing unit release leversFusing unit paper guide Open to remove misfed paper Document feeder trayOperation Panel SPF indicator only on the SPF model Original Size Enter key Enter / Original Size indicatorsPaper Size indicators Auto Image key Auto % / indicatorChecking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeFor installation of the TD cartridge, see the next Gently lift and pull out the paper tray until it stopsInstalling the TD Cartridge TD cartridge replacement required indicator will go outClose the front cover Power OFF Power on and OFFPower on Power Save ModesPaper Paper tray type Paper type Size Weight CapacityLoading Paper Special papersLocks in place Loading PaperLoading the paper tray Fan the paperUnfold the bypass tray Important points when inserting paper in the bypass trayLoading the bypass tray Set the paper guides to the copy paper widthChanging a TRAY’S Paper Size Setting EnvelopesImportant points when using the printer mode Press the Start key and then press the Paper Size Enter keyNormal Copying Copying from the document glassOpen the document cover/SPF, and place the original Copying from the SPF only on the SPF model Set the originals face up in the document feeder traySet the number of copies Auto paper select mode Two-tray model only Selecting the Tray Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Original typesAutomatic Ratio Selection Setting the Number of CopiesREDUCTION/ENLAREGMENT/ZOOM Original position Selectable ratiosManual Ratio Selection Selecting a preset ratioFine adjustment of the ratio Press the Auto Image key Auto %XY Zoom copying Press the Copy ratio display keyDown the Copy ratio display key TWO-SIDED Copying Using the Bypass Tray Copy original aPlace original B as shown below Dual page Copying Interrupting a Copy RUN Press the Interrupt key to interrupt the copy runReplace the previous originals and press the Start key Make sure that paper is loaded in the tray Using the Printer ModeBasic Procedure for Printing Click the Print button or the OK button to begin printingPausing a print job Using the Scanner ModeScanning Using the Keys on the Machine When Use close paper size is disabledPress a Scan Menu key to begin Scanning from Your ComputerScan Menu keys and the Button Manager scan menu ScanningPrinter During printing Operation in COPY, PRINTER, and Scanner ModesDuring copying Scanner During scan previewAdjusting the Automatic Exposure Level Photo indicator stops blinking and lights steadily Enabling Toner Save ModeWhen enabling toner Save mode, make sureCustomising Settings User ProgramsMinimum Explanation300dpi Short beepSelecting a Setting for a User Program Base settingsAuditing Mode Settings Settings for Auditing ModeAuditing Mode Factory default settingsSelecting Auditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.41Account number change Auditing modeAccount number entry Account number deletionResetting account Copying when Auditing mode is enabledTroubleshooting MACHINE/COPYING Problems Pieces of paper inside machine Problem Cause and solution Misfeed occursPaper is not loaded properly Paper misfeed Too much paper is loaded in the trayPower Save indicator is only lit Lit Any other indicators are litPower Save indicator is Original smudged or blotchyPrinting and Scanning Problems Uneven Printed image is dirtyRuns off the paper Original is smudged or blotchy You have not specified a suitable resolutionBrightness and contrast settings are not suitable Poor scanning qualityClick Add or Remove Programs Removing the softwareClick the start button, and then click Control Panel If you need to remove the software, follow these stepsIndicators and Display Messages Misfeed Removal Remove the misfed originalAL-1644 AL-1633 Misfeed indicator will go out Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the paper feed areaMisfeed in the fusing area Allow easier removalMisfed paper during Misfeed in the transport area Close the side coverBe careful not to tear the misfed paper during removal Misfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Close the lower side cover Open the lower side coverClose the lower paper tray Remove the misfed paper Grasp the handle to open the lower side coverReplacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Total output count Checking the Total Output CountChecking the Total Output Count Total copy countPress the Light key to return to the normal display Checking the Toner Level and Drum Cartridge LifeToner Level Hold down the Clear key for more than 5 secondsRoutine Maintenance Cleaning the Document Glass and SPF/ Document CoverCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Proper Storage Storage of SuppliesSupply Part Numbers Supply listAccessories p.12 When moving this machine, follow the procedure belowMoving Instructions Specifications SPF only on the SPF model Specifications Printer FunctionScanner Function Software License Page Symbols IndexPrinting and scanning problems TD cartridge replacement requiredTray Select key 11, 19, 21, 23 Troubleshooting Normal copyingMachine settings Problem occursIndicators, lit and blinking Memo Memo Class Laser Product Laser Klasse Page 2004E