Sharp AL-1644, AL-1633 Storage of Supplies, Supply Part Numbers, Proper Storage, Supply list

Page 70

7

Chapter 7

SUPPLIES

STORAGE OF SUPPLIES

Standard supplies for this product that are to be replaced by the user are paper, TD cartridge and drum cartridge.

For best copying results, be sure to use only SHARP products.

Only genuine SHARP consumables carry the Genuine Supplies label.

GENUINE SUPPLIES

SUPPLY PART NUMBERS

When ordering supplies, please use the correct part numbers as listed below.

Caution

Be sure to use only genuine SHARP parts

and supplies.

Supply list

Supply

Part number

Usable life

 

 

 

TD cartridge

AL-161TD

Approx. 9,000 sheets*

 

 

 

Drum cartridge

AL-160DR (N)

Approx. 30,000 sheets

 

 

 

*Based on copying onto A4 size paper at 5% toned area

(The life of the TD cartridge which has been included in the machine at the factory is approximately 4,500 sheets.)

PROPER STORAGE

Store the supplies in a location that is:

clean and dry,

at a stable temperature,

not exposed to direct sunlight.

Store paper in the wrapper and lying

flat.

Paper stored out of the wrapper or in packages standing on end may curl or get damp, resulting in paper misfeeds.

68

Image 70
Contents AL-1633 AL-1644Page Contents Troubleshooting Misfeed in the SPF only on the SPF modelChanges, e.g., near an Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Air conditioner orTrademark acknowledgements Software Setup Guide separate manual Using the ManualOnline Manual on the accessory CD-ROM Environmental InformationThis manual covers the following models Conventions Used in this ManualSPF Differences Between Models Model AL-1644 AL-1633 AppearanceMain Features Part Names and Functions Parallel port Fusing unit release leversFusing unit paper guide Open to remove misfed paper Document feeder trayOperation Panel SPF indicator only on the SPF model Original Size Enter key Enter / Original Size indicatorsPaper Size indicators Auto Image key Auto % / indicatorChecking Packed Components and Accessories UnpackingSET-UP Install the TD cartridgeFor installation of the TD cartridge, see the next Gently lift and pull out the paper tray until it stopsTD cartridge replacement required indicator will go out Installing the TD CartridgeClose the front cover Power OFF Power on and OFFPower on Power Save ModesPaper Paper tray type Paper type Size Weight CapacityLoading Paper Special papersLocks in place Loading PaperLoading the paper tray Fan the paperUnfold the bypass tray Important points when inserting paper in the bypass trayLoading the bypass tray Set the paper guides to the copy paper widthChanging a TRAY’S Paper Size Setting EnvelopesImportant points when using the printer mode Press the Start key and then press the Paper Size Enter keyCopying from the document glass Normal CopyingOpen the document cover/SPF, and place the original Set the originals face up in the document feeder tray Copying from the SPF only on the SPF modelSet the number of copies Auto paper select mode Two-tray model only Selecting the Tray Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Original typesAutomatic Ratio Selection Setting the Number of CopiesREDUCTION/ENLAREGMENT/ZOOM Original position Selectable ratiosManual Ratio Selection Selecting a preset ratioFine adjustment of the ratio Press the Auto Image key Auto %XY Zoom copying Press the Copy ratio display keyDown the Copy ratio display key Copy original a TWO-SIDED Copying Using the Bypass TrayPlace original B as shown below Dual page Copying Press the Interrupt key to interrupt the copy run Interrupting a Copy RUNReplace the previous originals and press the Start key Make sure that paper is loaded in the tray Using the Printer ModeBasic Procedure for Printing Click the Print button or the OK button to begin printingPausing a print job Using the Scanner ModeScanning Using the Keys on the Machine When Use close paper size is disabledPress a Scan Menu key to begin Scanning from Your ComputerScan Menu keys and the Button Manager scan menu ScanningPrinter During printing Operation in COPY, PRINTER, and Scanner ModesDuring copying Scanner During scan previewAdjusting the Automatic Exposure Level Photo indicator stops blinking and lights steadily Enabling Toner Save ModeWhen enabling toner Save mode, make sureCustomising Settings User ProgramsMinimum Explanation300dpi Short beepSelecting a Setting for a User Program Base settingsAuditing Mode Settings Settings for Auditing ModeAuditing Mode Factory default settingsSelecting Auditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.41Account number change Auditing modeAccount number entry Account number deletionResetting account Copying when Auditing mode is enabledTroubleshooting MACHINE/COPYING Problems Pieces of paper inside machine Problem Cause and solution Misfeed occursPaper is not loaded properly Paper misfeed Too much paper is loaded in the trayPower Save indicator is only lit Lit Any other indicators are litPower Save indicator is Original smudged or blotchyPrinting and Scanning Problems Printed image is dirty UnevenRuns off the paper Original is smudged or blotchy You have not specified a suitable resolutionBrightness and contrast settings are not suitable Poor scanning qualityClick Add or Remove Programs Removing the softwareClick the start button, and then click Control Panel If you need to remove the software, follow these stepsIndicators and Display Messages Remove the misfed original Misfeed RemovalAL-1644 AL-1633 Misfeed indicator will go out Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the paper feed areaAllow easier removal Misfeed in the fusing areaMisfed paper during Close the side cover Misfeed in the transport areaBe careful not to tear the misfed paper during removal Close the upper paper tray Misfeed in the Upper Paper TrayPush the upper paper tray in completely Close the lower side cover Open the lower side coverClose the lower paper tray Remove the misfed paper Grasp the handle to open the lower side coverReplacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Total output count Checking the Total Output CountChecking the Total Output Count Total copy countPress the Light key to return to the normal display Checking the Toner Level and Drum Cartridge LifeToner Level Hold down the Clear key for more than 5 secondsCleaning the Document Glass and SPF/ Document Cover Routine MaintenanceCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Proper Storage Storage of SuppliesSupply Part Numbers Supply listWhen moving this machine, follow the procedure below Accessories p.12Moving Instructions Specifications SPF only on the SPF model Specifications Printer FunctionScanner Function Software License Page Symbols IndexPrinting and scanning problems TD cartridge replacement requiredTray Select key 11, 19, 21, 23 Troubleshooting Normal copyingProblem occurs Machine settingsIndicators, lit and blinking Memo Memo Class Laser Product Laser Klasse Page 2004E