Sharp AL-1633, AL-1644 Power on and OFF, Power OFF, Power Save Modes, Initial settings

Page 17

POWER ON AND OFF

The power switch is located on the left side of the machine.

POWER ON

Turn the power switch to the "ON" position

It will take about 45 seconds for the machine to warm up. While the machine is warming up, the POWER SAVE

indicator (

) will blink.

(The POWER SAVE

indicator (

) will go off

when the machine is ready to copy.)

However, you can make desired settings and press

the [START] key ( ) during warm-up. Copying will start after warm-up.

POWER OFF

Make sure that the machine is not in operation and then turn the power switch to the "OFF" position.

If the power switch is turned off while the

machine is in operation, 1 a misfeed may occur and

the job that was in progress will be cancelled.

Check the following to make sure the machine is not in operation:

•The START indicator is lit. (Initial state)

•The POWER SAVE indicator () is lit. ("Preheat mode" or "Auto power shut-off" mode)

•

The machine reverts to the initial settings when it is first turned on, when the [CLEAR ALL] key (

) is pressed,

Note

or when no keys are pressed for the preset "Auto clear time" following the end of a copy job. When the machine

reverts to the initial settings, all settings and functions selected to that point are canceled. The "Auto clear time" can be changed in the user programs. (p.38)

•The machine is initially set to automatically enter power save mode if not used for copying, printing, or scanning for a preset period of time. This setting can be changed in the user programs. (p.38)

Power Save Modes

The machine has two power save modes to reduce overall power consumption thereby reducing the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto power shut-off mode".

Preheat mode

This function automatically switches the machine to a low power consumption state if the set duration of time elapses without the machine being used when the power is on. The POWER SAVE indicator () lights up, however, the keys on the operation panel can be used. Normal operation automatically resumes when a key on the operation panel is pressed, an original is placed, or a print job is received.

Auto power shut-off mode

This function automatically switches the machine to a state that consumes even less power than preheat mode if the set duration of time elapses without the machine being used when the power is on. All lights except the POWER SAVE indicator () and ON LINE indicator () go off. To resume normal operation, press the [START] key ( ). Normal operation also resumes automatically when a print job is received or scanning is begun from a computer. While in auto power shut-off mode, no keys (except the [START] key ( )) can be used.

Note The preheat activation time and the "Auto power shut-off timer" can be changed using user programs. It is suggested that you set times that are appropriate for your usage of the machine. (p.38)

Initial settings

The machine assumes the initial settings when it is first turned on, when the [CLEAR ALL] key ( ) is pressed, and approximately one minute after the last copy is made in any mode.

Copy ratio: 100%, Exposure: Automatic

Copy quantity: 0, All special copier modes: Off

Auto paper selection: On, Paper feed station: The tray selected in the "Default tray setting" in the user programs.(p.39)

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents AL-1644 AL-1633Page Contents Misfeed in the SPF only on the SPF model TroubleshootingDo not install your machine in areas that are Important Points When Selecting AN Installation SiteChanges, e.g., near an Air conditioner orTrademark acknowledgements Online Manual on the accessory CD-ROM Using the ManualSoftware Setup Guide separate manual Environmental InformationSPF Differences Between Models Conventions Used in this ManualThis manual covers the following models Model AL-1644 AL-1633 AppearanceMain Features Part Names and Functions Fusing unit paper guide Open to remove misfed paper Fusing unit release leversParallel port Document feeder trayOperation Panel Paper Size indicators Original Size Enter key Enter / Original Size indicatorsSPF indicator only on the SPF model Auto Image key Auto % / indicatorUnpacking Checking Packed Components and AccessoriesFor installation of the TD cartridge, see the next Install the TD cartridgeSET-UP Gently lift and pull out the paper tray until it stopsClose the front cover Installing the TD CartridgeTD cartridge replacement required indicator will go out Power on Power on and OFFPower OFF Power Save ModesLoading Paper Paper tray type Paper type Size Weight CapacityPaper Special papersLoading the paper tray Loading PaperLocks in place Fan the paperLoading the bypass tray Important points when inserting paper in the bypass trayUnfold the bypass tray Set the paper guides to the copy paper widthEnvelopes Changing a TRAY’S Paper Size SettingPress the Start key and then press the Paper Size Enter key Important points when using the printer modeOpen the document cover/SPF, and place the original Normal CopyingCopying from the document glass Set the number of copies Copying from the SPF only on the SPF modelSet the originals face up in the document feeder tray Auto paper select mode Two-tray model only Making a Copy Darker or Lighter Auto tray switching Two-tray model onlySelecting the Tray Original typesREDUCTION/ENLAREGMENT/ZOOM Setting the Number of CopiesAutomatic Ratio Selection Original position Selectable ratiosFine adjustment of the ratio Selecting a preset ratioManual Ratio Selection Press the Auto Image key Auto %Press the Copy ratio display key XY Zoom copyingDown the Copy ratio display key Place original B as shown below TWO-SIDED Copying Using the Bypass TrayCopy original a Dual page Copying Replace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Basic Procedure for Printing Using the Printer ModeMake sure that paper is loaded in the tray Click the Print button or the OK button to begin printingScanning Using the Keys on the Machine Using the Scanner ModePausing a print job When Use close paper size is disabledScan Menu keys and the Button Manager scan menu Scanning from Your ComputerPress a Scan Menu key to begin ScanningDuring copying Operation in COPY, PRINTER, and Scanner ModesPrinter During printing Scanner During scan previewAdjusting the Automatic Exposure Level When enabling toner Enabling Toner Save ModePhoto indicator stops blinking and lights steadily Save mode, make sureUser Programs Customising Settings300dpi ExplanationMinimum Short beepBase settings Selecting a Setting for a User ProgramAuditing Mode Settings for Auditing ModeAuditing Mode Settings Factory default settingsFor the setting codes, see Auditing Mode SETTINGS. p.41 Selecting Auditing Mode SettingsAccount number entry Auditing modeAccount number change Account number deletionCopying when Auditing mode is enabled Resetting accountTroubleshooting MACHINE/COPYING Problems Paper is not loaded properly Problem Cause and solution Misfeed occursPieces of paper inside machine Paper misfeed Too much paper is loaded in the trayPower Save indicator is Any other indicators are litPower Save indicator is only lit Lit Original smudged or blotchyPrinting and Scanning Problems Runs off the paper UnevenPrinted image is dirty Brightness and contrast settings are not suitable You have not specified a suitable resolutionOriginal is smudged or blotchy Poor scanning qualityClick the start button, and then click Control Panel Removing the softwareClick Add or Remove Programs If you need to remove the software, follow these stepsIndicators and Display Messages AL-1644 AL-1633 Misfeed RemovalRemove the misfed original Misfeed in the Bypass Tray Misfeed indicator will go outMisfeed in the paper feed area Misfeed in the MachineMisfed paper during Misfeed in the fusing areaAllow easier removal Be careful not to tear the misfed paper during removal Misfeed in the transport areaClose the side cover Push the upper paper tray in completely Misfeed in the Upper Paper TrayClose the upper paper tray Close the lower paper tray Remove the misfed paper Open the lower side coverClose the lower side cover Grasp the handle to open the lower side coverReplacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Checking the Total Output Count Checking the Total Output CountTotal output count Total copy countToner Level Checking the Toner Level and Drum Cartridge LifePress the Light key to return to the normal display Hold down the Clear key for more than 5 secondsCleaning the Bypass Tray Paper Feed Roller Routine MaintenanceCleaning the Document Glass and SPF/ Document Cover Cleaning the Transfer Charger Supply Part Numbers Storage of SuppliesProper Storage Supply listMoving Instructions Accessories p.12When moving this machine, follow the procedure below Specifications Printer Function SPF only on the SPF model SpecificationsScanner Function Software License Page Index SymbolsTray Select key 11, 19, 21, 23 Troubleshooting TD cartridge replacement requiredPrinting and scanning problems Normal copyingIndicators, lit and blinking Machine settingsProblem occurs Memo Memo Class Laser Product Laser Klasse Page 2004E
Top Page Image Contents