Sharp AL-1633, AL-1644 operation manual Close the front cover and side cover

Page 65

TROUBLESHOOTING

5 Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides.

Caution

Do not touch the drum cartridge (green portion). Doing so may damage the drum and cause smudges on copies.

6 Remove the protective cover from the drum cartridge and then push the cartridge all the way into the machine.

7 Insert the TD cartridge along the guides until it locks in place.

If there is any dirt or dust on the TD cartridge, remove it before installing the cartridge.

8 Close the front cover and side cover.

The drum cartridge replacement required

indicator ( ) will go out.

• Before closing the front cover, make sure

Note that the TD cartridge and drum cartridge is correctly installed.

•When closing the front cover, gently hold both ends.

Image 65

Contents AL-1644 AL-1633Page Contents Misfeed in the SPF only on the SPF model TroubleshootingDo not install your machine in areas that are Important Points When Selecting AN Installation SiteChanges, e.g., near an Air conditioner orTrademark acknowledgements Online Manual on the accessory CD-ROM Using the ManualSoftware Setup Guide separate manual Environmental InformationSPF Differences Between Models Conventions Used in this ManualThis manual covers the following models Model AL-1644 AL-1633 AppearanceMain Features Part Names and Functions Fusing unit paper guide Open to remove misfed paper Fusing unit release leversParallel port Document feeder trayOperation Panel Paper Size indicators Original Size Enter key Enter / Original Size indicatorsSPF indicator only on the SPF model Auto Image key Auto % / indicatorUnpacking Checking Packed Components and AccessoriesFor installation of the TD cartridge, see the next Install the TD cartridgeSET-UP Gently lift and pull out the paper tray until it stopsClose the front cover Installing the TD CartridgeTD cartridge replacement required indicator will go out Power on Power on and OFFPower OFF Power Save ModesLoading Paper Paper tray type Paper type Size Weight CapacityPaper Special papersLoading the paper tray Loading PaperLocks in place Fan the paperLoading the bypass tray Important points when inserting paper in the bypass trayUnfold the bypass tray Set the paper guides to the copy paper widthEnvelopes Changing a TRAY’S Paper Size SettingPress the Start key and then press the Paper Size Enter key Important points when using the printer modeOpen the document cover/SPF, and place the original Normal CopyingCopying from the document glass Set the number of copies Copying from the SPF only on the SPF modelSet the originals face up in the document feeder tray Auto paper select mode Two-tray model only Making a Copy Darker or Lighter Auto tray switching Two-tray model onlySelecting the Tray Original typesREDUCTION/ENLAREGMENT/ZOOM Setting the Number of CopiesAutomatic Ratio Selection Original position Selectable ratiosFine adjustment of the ratio Selecting a preset ratioManual Ratio Selection Press the Auto Image key Auto %Press the Copy ratio display key XY Zoom copyingDown the Copy ratio display key Place original B as shown below TWO-SIDED Copying Using the Bypass TrayCopy original a Dual page Copying Replace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Basic Procedure for Printing Using the Printer ModeMake sure that paper is loaded in the tray Click the Print button or the OK button to begin printingScanning Using the Keys on the Machine Using the Scanner ModePausing a print job When Use close paper size is disabledScan Menu keys and the Button Manager scan menu Scanning from Your ComputerPress a Scan Menu key to begin ScanningDuring copying Operation in COPY, PRINTER, and Scanner ModesPrinter During printing Scanner During scan previewAdjusting the Automatic Exposure Level When enabling toner Enabling Toner Save ModePhoto indicator stops blinking and lights steadily Save mode, make sureUser Programs Customising Settings300dpi ExplanationMinimum Short beepBase settings Selecting a Setting for a User ProgramAuditing Mode Settings for Auditing ModeAuditing Mode Settings Factory default settingsFor the setting codes, see Auditing Mode SETTINGS. p.41 Selecting Auditing Mode SettingsAccount number entry Auditing modeAccount number change Account number deletionCopying when Auditing mode is enabled Resetting accountTroubleshooting MACHINE/COPYING Problems Paper is not loaded properly Problem Cause and solution Misfeed occursPieces of paper inside machine Paper misfeed Too much paper is loaded in the trayPower Save indicator is Any other indicators are litPower Save indicator is only lit Lit Original smudged or blotchyPrinting and Scanning Problems Runs off the paper UnevenPrinted image is dirty Brightness and contrast settings are not suitable You have not specified a suitable resolutionOriginal is smudged or blotchy Poor scanning qualityClick the start button, and then click Control Panel Removing the softwareClick Add or Remove Programs If you need to remove the software, follow these stepsIndicators and Display Messages AL-1644 AL-1633 Misfeed RemovalRemove the misfed original Misfeed in the Bypass Tray Misfeed indicator will go outMisfeed in the paper feed area Misfeed in the MachineMisfed paper during Misfeed in the fusing areaAllow easier removal Be careful not to tear the misfed paper during removal Misfeed in the transport areaClose the side cover Push the upper paper tray in completely Misfeed in the Upper Paper TrayClose the upper paper tray Close the lower paper tray Remove the misfed paper Open the lower side coverClose the lower side cover Grasp the handle to open the lower side coverReplacing the TD Cartridge Replacing the Drum Cartridge Drum cartridge replacement required Indicator will go out Checking the Total Output Count Checking the Total Output CountTotal output count Total copy countToner Level Checking the Toner Level and Drum Cartridge LifePress the Light key to return to the normal display Hold down the Clear key for more than 5 secondsCleaning the Bypass Tray Paper Feed Roller Routine MaintenanceCleaning the Document Glass and SPF/ Document Cover Cleaning the Transfer Charger Supply Part Numbers Storage of SuppliesProper Storage Supply listMoving Instructions Accessories p.12When moving this machine, follow the procedure below Specifications Printer Function SPF only on the SPF model SpecificationsScanner Function Software License Page Index SymbolsTray Select key 11, 19, 21, 23 Troubleshooting TD cartridge replacement requiredPrinting and scanning problems Normal copyingIndicators, lit and blinking Machine settingsProblem occurs Memo Memo Class Laser Product Laser Klasse Page 2004E