Sigma SQM-160 manual Chapter Operation Introduction, Menu Selection

Page 12

Chapter 2

Operation

2.0Introduction

This section details the operation of the SQM-160 menus and front panel controls. It is arranged by common user tasks.

Note: User actions with front panel controls are indicated by a Box. Results shown on displays, are indicated by a Dashed Box.

2.1Menu Selection

Two menus provide control of the SQM-160 programming. The Film Parameters Menu allows you to customize each of the nine stored films. The System Parameters Menu sets values that remain constant for all films.

Note: If Crystal Life is shown on the SQM-160 displays, press the Xtal Life switch to return the displays to rate/thickness or frequency display.

The Configuration Section of the SQM-160 front panel contains four switches used to access the program menus. Within the program menus, the Control Knob is also used

to adjust values and select menu choices. In program mode, Display 1 shows the parameter to be changed. Display 2 shows the selected parameter’s value.

To enter the Film Parameters Menu, press the Program switch. The SQM-160 displays the currently active film. Turn the control knob to select a different film, then press Next to display the first parameter for the selected film.

To enter the System Parameters Menu, press the Program switch. Then press Prev to display the first system parameter.

Rate A/s

Thickness kA

1

 

2

 

 

 

 

 

 

 

3

 

4

 

 

 

 

 

 

 

5

 

6

 

 

Zero

 

 

 

 

Crystal Status

 

 

 

Open

 

 

 

 

 

 

Time

Time SP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Closed

 

 

Thk SP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Xtal Life

Shutter

 

 

 

 

Next

Prev

Clear

Program

 

 

 

 

Final Thk

 

 

 

 

 

Control

Sigma

 

SQM-160

 

 

Configuration

 

 

 

 

 

 

Σinstruments

Rate/Thickness Monitor

 

 

 

Press NEXT to

Press PREV then

Press

move thru the

NEXT to move

PROGRAM

Film menu

thru the

to access

 

System menu

menus

2-1

Image 12
Contents SQM-160 Safety Information Safety SymbolsWarranty Information Limitation of WarrantyReturn Policy Table of Contents Chapter Quick Start Chapter OperationChapter Options Chapter MonComm SoftwareChapter Maintenance AppendixInstallation Chapter Quick Start IntroductionChapter Quick Start Front Panel ControlsChapter Quick Start Rear Panel Rear Panel ConnectionsChapter Quick Start System Connections System ComponentsChapter Quick Start Film Setup Chapter Quick Start Depositing a Film Chapter Operation Introduction Menu SelectionChapter Operation Film Parameters Setup Description Range Default Units Film Selection Film Parameters Menu Sub-MenuDisplay Chapter Operation System Parameters Setup Timebase SIM Mode FRQ Disp Rate RES Ratefilt Baudrate Etch System Parameters Menu Sub-MenuDisplay xTOOLING FMIN/MAX Freq MIN Freq MAXChapter Operation Sensor Selection Chapter Operation Sensor Min/Max Frequency Chapter Operation Sensor Tooling Chapter Operation Rate/Thickness or Frequency Display Crystal Life DisplaySimulate Mode Chapter Operation Zero ThicknessShutter Operation Chapter Options Introduction Chapter Options Four Sensor Card Analog Output CardChapter MonComm Software Introduction Run MonCommChapter MonComm Software Add and Delete Films To add a new film to the Films ListTo delete a film from the Films List Chapter MonComm Software Download Films To add or replace a film in the Download ListTo remove a film from the Download List To download the films in the Download ListChapter MonComm Software Graph Data To Adjust the Graph’s Scope Save DataLoad Defaults Chapter MonComm Software Edit System ParametersChapter Maintenance Introduction Fuse ReplacementAppendix Material Parameters Appendix Specifications Relay I/O Connector Rear View Pins Type DescriptionAppendix O Connections Safety Appendix Declaration of ConformityDeclares that the product Product Model SQM-160 Product Options All Options