AMX NXA-WAP250G manual AMX Limited Warranty and Disclaimer

Page 2

AMX Limited Warranty and Disclaimer

AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions:

Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year.

Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one

(1) year.

AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.

Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.

AMX Software is warranted for a period of ninety (90) days.

Batteries and incandescent lamps are not covered under the warranty.

This warranty extends only to products purchased directly from AMX or an Authorized AMX Dealer.

All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number.

AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Dealer for a third party.

This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury.

Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY.

Image 2
Contents NXA-WAP250G AMX Limited Warranty and Disclaimer Table of Contents Appendix a Troubleshooting Federal Communication Commission Interference Statement Important Note FCC Radiation Exposure StatementEC Conformance Declaration Specifications OverviewEthernet Port Power ConnectorReset Button Installation Twisted-Pair Cable Assignments Access Point ConfigurationStraight-Through Wiring LED Indicators Ethernet LAN Port Antenna Power Socket CAT5 WallMount SlotsReset Button Overview Hardware DescriptionDiagnosing Access Point Indicators Symptom Action Power LED is OffSelecting an Operation Mode Access Point ModeAccess Point Mode Roaming Access Point Mode roaming for mobile usersAccess Point Mode Repeater and Bridge Mode Bridge ModeLogin Logging into the Web InterfaceUsing the Setup Wizard Operation Mode SettingNetwork Setting Setup Wizard Network SettingSetup Wizard Network Setting PPoE settings Dhcp Server/NAT Setting Wireless VAP #1 SettingSetup Wizard Wireless VAP #1 Setting WEP settings Wireless VAP #2 Setting Setup Wizard Wireless VAP #2 SettingFinish and Reboot Setup Wizard Wizard configuration donePage System Configuration Information NetworkInformation System System InformationInformation Client Client InformationInformation Network Information Event LogSystem Setting System Setting AdministrationSystem Setting Vlan Status / Operation Mode Operation ModesSystem Setting VAP Management System Settings Reset SystemWireless VAP Settings Wireless VAP Settings Basic SettingWireless VAP Settings Channel Setting Wireless VAP 1 Setting Basic SettingsWireless VAP Settings WEP Setting Authentication Mode Select Open or SharedSystem Configuration Wireless VAP Settings WPA / WPA2 Setting WPA, WPA2, WPA-WPA2 Mix ModeNetwork Settings Network Settings Dhcp Client SettingNetwork Settings Dhcp Server/NAT Setting Network Settings Dhcp Server/NAT SettingsNetwork Settings PPPoE Setting Network Settings PPPoE SettingsNetwork Settings Radius Server Setting Network Settings Radius Server SettingsTime Setting Time and LogUpgrade via the Web Updating FirmwareUpgrade via a Remote Server Firmware Upgrade Local FileSystem Configuration Page Website for free Tftp Server If Your WAP250G Is Stuck on the Emergent Recovery ScreenChoose Download site and Install Tftp Server Ethernet Connectivity Change Tftp Server SettingsCopy Firmware file Launch Tftp ServerTftp Server Configuration dialog Re-Connect to WAP 250GPage Glossary NXA-WAP250G 802.11b/g Wireless Access Point It’s Your World Take Control