AMX NXA-WAP250G manual Copy Firmware file, Ethernet Connectivity, Launch Tftp Server

Page 48

Appendix A: Troubleshooting

Step 3: Copy Firmware file

1.E-mail a copy of the firmware file ZZ-IMG.BIN (Firmware file 1.0.4.6) to the dealer.

2.Copy the file into the C:\TFTP-ROOT directory

Step 4: Ethernet Connectivity

1.Verify the Ethernet port is enabled and connect an Ethernet cable from the laptop to the WAP250G.

2.Highlight My Network Places; Right-clickProperties, Highlight TCP/IP Settings and click Properties.

3.Assign a static IP Address on the same network as the WAP250

4.Click OK.

5.Click OK.

6.Click Start/Run and type CMD.

7.Ping IP Address of the WAP250G to verify connectivity.

Step 5: Launch TFTP Server

1.Start\Run\Program

2.Select Solarwinds Free Tools.

3.Select TFTP Server - the following window launches (FIG. 42):

FIG. 42 SolarWinds.NET TFTP Server dialog

4.The IP Address should reflect the same IP Address of your Ethernet port on your laptop and the default directory (C:\TFTP-Root) is displayed on the bottom left.

Step 6: Change TFTP Server Settings

1.Select File.

2.Select Configure.

3.Select the Security Tab and change selection to Transmit and Receive Files (FIG. 43).

4.Click OK.

44

NXA-WAP250G 802.11b/g Wireless Access Point

Image 48
Contents NXA-WAP250G AMX Limited Warranty and Disclaimer Table of Contents Appendix a Troubleshooting Federal Communication Commission Interference Statement Important Note FCC Radiation Exposure StatementEC Conformance Declaration Specifications OverviewPower Connector Reset ButtonEthernet Port Installation Access Point Configuration Straight-Through WiringTwisted-Pair Cable Assignments Ethernet LAN Port Antenna Power Socket CAT5 WallMount Slots Reset Button OverviewLED Indicators Hardware DescriptionDiagnosing Access Point Indicators Symptom Action Power LED is OffSelecting an Operation Mode Access Point ModeAccess Point Mode Roaming Access Point Mode roaming for mobile usersAccess Point Mode Repeater and Bridge Mode Bridge ModeLogin Logging into the Web InterfaceUsing the Setup Wizard Operation Mode SettingNetwork Setting Setup Wizard Network SettingSetup Wizard Network Setting PPoE settings Dhcp Server/NAT Setting Wireless VAP #1 SettingSetup Wizard Wireless VAP #1 Setting WEP settings Wireless VAP #2 Setting Setup Wizard Wireless VAP #2 SettingFinish and Reboot Setup Wizard Wizard configuration donePage System Configuration Information NetworkInformation System System InformationInformation Client Client InformationInformation Network Information Event LogSystem Setting System Setting AdministrationSystem Setting Vlan Status / Operation Mode Operation ModesSystem Setting VAP Management System Settings Reset SystemWireless VAP Settings Wireless VAP Settings Basic SettingWireless VAP Settings Channel Setting Wireless VAP 1 Setting Basic SettingsWireless VAP Settings WEP Setting Authentication Mode Select Open or SharedSystem Configuration Wireless VAP Settings WPA / WPA2 Setting WPA, WPA2, WPA-WPA2 Mix ModeNetwork Settings Network Settings Dhcp Client SettingNetwork Settings Dhcp Server/NAT Setting Network Settings Dhcp Server/NAT SettingsNetwork Settings PPPoE Setting Network Settings PPPoE SettingsNetwork Settings Radius Server Setting Network Settings Radius Server SettingsTime Setting Time and LogUpgrade via the Web Updating FirmwareUpgrade via a Remote Server Firmware Upgrade Local FileSystem Configuration Page If Your WAP250G Is Stuck on the Emergent Recovery Screen Choose Download site and Install Tftp ServerWebsite for free Tftp Server Change Tftp Server Settings Copy Firmware fileEthernet Connectivity Launch Tftp ServerTftp Server Configuration dialog Re-Connect to WAP 250GPage Glossary NXA-WAP250G 802.11b/g Wireless Access Point It’s Your World Take Control