AMX NXA-WAP250G manual Federal Communication Commission Interference Statement

Page 5

Compliances

Compliances

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE: FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters (8 inches) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.

NXA-WAP250G 802.11b/g Wireless Access Point

1

 

 

Image 5
Contents NXA-WAP250G AMX Limited Warranty and Disclaimer Table of Contents Appendix a Troubleshooting Important Note FCC Radiation Exposure Statement Federal Communication Commission Interference StatementEC Conformance Declaration Overview SpecificationsEthernet Port Power ConnectorReset Button Installation Twisted-Pair Cable Assignments Access Point ConfigurationStraight-Through Wiring Reset Button Overview Ethernet LAN Port Antenna Power Socket CAT5 WallMount SlotsLED Indicators Hardware DescriptionSymptom Action Power LED is Off Diagnosing Access Point IndicatorsAccess Point Mode Selecting an Operation ModeAccess Point Mode roaming for mobile users Access Point Mode RoamingBridge Mode Access Point Mode Repeater and Bridge ModeLogging into the Web Interface LoginOperation Mode Setting Using the Setup WizardSetup Wizard Network Setting Network SettingSetup Wizard Network Setting PPoE settings Wireless VAP #1 Setting Dhcp Server/NAT SettingSetup Wizard Wireless VAP #1 Setting WEP settings Setup Wizard Wireless VAP #2 Setting Wireless VAP #2 SettingSetup Wizard Wizard configuration done Finish and RebootPage System Configuration Network InformationSystem Information Information SystemClient Information Information ClientInformation Event Log Information NetworkSystem Setting Administration System SettingOperation Modes System Setting Vlan Status / Operation ModeSystem Settings Reset System System Setting VAP ManagementWireless VAP Settings Basic Setting Wireless VAP SettingsWireless VAP 1 Setting Basic Settings Wireless VAP Settings Channel SettingAuthentication Mode Select Open or Shared Wireless VAP Settings WEP SettingSystem Configuration WPA, WPA2, WPA-WPA2 Mix Mode Wireless VAP Settings WPA / WPA2 SettingNetwork Settings Dhcp Client Setting Network SettingsNetwork Settings Dhcp Server/NAT Settings Network Settings Dhcp Server/NAT SettingNetwork Settings PPPoE Settings Network Settings PPPoE SettingNetwork Settings Radius Server Settings Network Settings Radius Server SettingTime and Log Time SettingUpdating Firmware Upgrade via the WebFirmware Upgrade Local File Upgrade via a Remote ServerSystem Configuration Page Website for free Tftp Server If Your WAP250G Is Stuck on the Emergent Recovery ScreenChoose Download site and Install Tftp Server Copy Firmware file Change Tftp Server SettingsEthernet Connectivity Launch Tftp ServerRe-Connect to WAP 250G Tftp Server Configuration dialogPage Glossary NXA-WAP250G 802.11b/g Wireless Access Point It’s Your World Take Control