AMX NXA-WAP250G manual If Your WAP250G Is Stuck on the Emergent Recovery Screen

Page 47

Appendix A: Troubleshooting

Appendix A: Troubleshooting

Overview

Check the following items before you contact local Technical Support.

1.If wireless clients cannot access the network, check the following:

Be sure the NXA-WAP250G and the wireless clients are configured with the same Service Set ID (SSID).

If authentication or encryption are enabled, ensure that the wireless clients are properly configured with the appropriate authentication or encryption keys.

2.If the NXA-WAP250G cannot be configured using a web browser:

Be sure to have configured the NXA-WAP250G with a valid IP address, subnet mask and default gateway.

If you are connecting to the NXA-WAP250G through the wired Ethernet interface, check the network cabling between the management station and the NXA-WAP250G. If you are connecting to NXA-WAP250G from a wireless client, ensure that you have a valid connection to the NXA-WAP250G.

3.If you forgot or lost the password:

Set the NXA-WAP250G to its default configuration by pressing the reset button on the back panel for 5 seconds or more. Connect to the web management interface using the default IP address 192.168.1.240. Then use the default user name “Admin” and the default password “1988” to access the management interface.

4.If all other recovery measure fail, and the NXA-WAP250G is still not functioning properly, take any of these steps:

Reset the NXA-WAP250G’s hardware using the web interface or through a power reset.

Reset the NXA-WAP250G to its default configuration by pressing the reset button on the back panel for 5 seconds or more. Connect to the web management interface using the default IP address 192.168.1.240, then use the default user name “Admin” and the default password “1988.”

If Your WAP250G Is Stuck on the Emergent Recovery Screen

Step 1: Website for free TFTP Server

1.Connect to the internet and enter the following link in the Address Bar on your web browser. http://www.solarwinds.net/downloads/index.aspx

2.Scroll to the bottom of the page and click Download Free TFTP Server located at the bottom of the page (you will have to enter name, e-mail etc…).

Step 2: Choose Download site and Install TFTP Server

1.Select any one of the three links that appear on the screen to begin download.

2.Click Run - to install software on your computer

3.Click Run again to begin the software install.

4.Select all of the defaults during the installation

NXA-WAP250G 802.11b/g Wireless Access Point

43

 

 

Page 46 Page 48
Image 47
Page 46 Page 48
Contents NXA-WAP250G AMX Limited Warranty and Disclaimer Table of Contents Appendix a Troubleshooting Important Note FCC Radiation Exposure Statement Federal Communication Commission Interference StatementEC Conformance Declaration Overview SpecificationsEthernet Port Power ConnectorReset Button Installation Twisted-Pair Cable Assignments Access Point ConfigurationStraight-Through Wiring Hardware Description Ethernet LAN Port Antenna Power Socket CAT5 WallMount SlotsReset Button Overview LED IndicatorsSymptom Action Power LED is Off Diagnosing Access Point IndicatorsAccess Point Mode Selecting an Operation ModeAccess Point Mode roaming for mobile users Access Point Mode RoamingBridge Mode Access Point Mode Repeater and Bridge ModeLogging into the Web Interface LoginOperation Mode Setting Using the Setup WizardSetup Wizard Network Setting Network SettingSetup Wizard Network Setting PPoE settings Wireless VAP #1 Setting Dhcp Server/NAT SettingSetup Wizard Wireless VAP #1 Setting WEP settings Setup Wizard Wireless VAP #2 Setting Wireless VAP #2 SettingSetup Wizard Wizard configuration done Finish and RebootPage System Configuration Network InformationSystem Information Information SystemClient Information Information ClientInformation Event Log Information NetworkSystem Setting Administration System SettingOperation Modes System Setting Vlan Status / Operation ModeSystem Settings Reset System System Setting VAP ManagementWireless VAP Settings Basic Setting Wireless VAP SettingsWireless VAP 1 Setting Basic Settings Wireless VAP Settings Channel SettingAuthentication Mode Select Open or Shared Wireless VAP Settings WEP SettingSystem Configuration WPA, WPA2, WPA-WPA2 Mix Mode Wireless VAP Settings WPA / WPA2 SettingNetwork Settings Dhcp Client Setting Network SettingsNetwork Settings Dhcp Server/NAT Settings Network Settings Dhcp Server/NAT SettingNetwork Settings PPPoE Settings Network Settings PPPoE SettingNetwork Settings Radius Server Settings Network Settings Radius Server SettingTime and Log Time SettingUpdating Firmware Upgrade via the WebFirmware Upgrade Local File Upgrade via a Remote ServerSystem Configuration Page Website for free Tftp Server If Your WAP250G Is Stuck on the Emergent Recovery ScreenChoose Download site and Install Tftp Server Launch Tftp Server Change Tftp Server SettingsCopy Firmware file Ethernet ConnectivityRe-Connect to WAP 250G Tftp Server Configuration dialogPage Glossary NXA-WAP250G 802.11b/g Wireless Access Point It’s Your World Take Control
Top Page Image Contents