Allied Telesis AT-SBX3161, X3112, AT-SBX31FAN, AT-SBX31GP24, AT-SBX31XZ4 Network Management Port

Page 25

Network

Management

Port

SwitchBlade x3112 Installation Guide

active controller and the active controller becomes the inactive or standby controller. During this process, the switch management function is swapped to the new active controller. In this case, the inactive AT- SBx31CFC becomes active immediately, and consequently, the Ethernet line cards are not affected or reset.

Caution

With two AT-SBx31CFC Fabric Control Cards installed, the switching fabric circuitry on each line card is shared. When you press the RESET button, the Ethernet network traffic flow through the switch is limited to 200 Gbps for up to two minutes. This is the time required for the inactive AT-SBx31CFC Fabric Control Card to reboot and for its switching fabric circuitry to become available again for switching network traffic.

Note

The RESET switch is specifically provided for resetting the AT-SBx31CFC Fabric Control Card. If you want to swap the controller function between the active and standby AT-SBx31CFC Fabric Control Cards, Allied Telesis recommends that you use the SWAP commands provided in the Switchblade x3112 Management Software. Refer the to the Software Reference for SwitchBlade® x3100 Series Switches on the ATI web site for specific information. Go to “Where to Find Web-based Guides” on page 13 for information about how to navigate to this document.

The Network Management (NET MGMT) port is a standard Ethernet, Fast Ethernet, and Gigabit Ethernet port. See Figure 8. This port provides for remote management of the SwitchBlade x3112 Switch when you connect it to a device on your network. If it is available in the chassis, you can connect it directly to one of the copper ports on an Ethernet line card.

1000 LINK	ACT
10/100 LINK	ACT
NET MGMT	CONSOLE
L/A
10/100/1000Base-T	RS-232
	1820

Figure 8 NET MGMT and CONSOLE Ports

The NET MGMT port is a standard RJ-45 8-pin connector and can operate at 10, 100, or 1000 Mbps in either half- or full-duplex mode. The cable requirements for this port can be found in the table “Cable Requirements for the 10/100/1000Base-T Management Port” on page 104. For the port

25

Image 25

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewComponent Description Reference IntroductionFront View of the AT-SBx3112 Chassis AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies SBx31CFC AT-SBx31CFC Fabric Control CardSystem Status LEDs AT-SBx31CFC Fabric Control Card Features Status LEDsState Description LEDLEDs State Description SBx Status LEDsEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE Power Budgeting AT-SBx31GP24 Power over EthernetPorts with Maximum Range Maximum # Class UsageAvailable at PoE PSU 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card LED AT-SBx31XZ4AT-SBx3161 Status LEDs AT-SBx3161 System Power SupplyStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 Status LEDs AT-SBx3165 PoE Power SupplyStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray Power LED on the AT-SBx31FAN Tray AT-SBx31FAN Tray PowerOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location. E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Reserving Vertical Rack Space Preparing the Equipment RackUnpacking AT-SBx3112 Chassis Front Panel Position Dimension Adjusting the BracketsFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Lifting AT-SBx3112 Chassis into Place Installing the AT SBx3112 Chassis Equipment RackRemoving the Front Panel Shipping Brace Screws Attaching the Grounding Wire to the Grounding Lug Installing Chassis Ground LugInstall the ground lug as displayed in Figure ESD Socket Protection Against Electrostatic Discharge ESDInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation SBx31CFC Starting a Local Management SessionInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Dimensions Physical SpecificationsWeight Appendix aPower Specifications Environmental SpecificationsEMI/RFI Safety and Electromagnetic Emissions CertificationsPin Signal Connectors and Port PinoutsPin Pair Signal Operating Cable RequirementsDistance