Allied Telesis AT-SBX3165, X3112, AT-SBX31FAN, AT-SBX31GP24, AT-SBX31XZ4 manual Console RS-232 Port

Page 26

Chapter 1: Overview

pinouts, refer to “Connectors and Port Pinouts” on page 102.

The default setting for the Management port is Auto-Negotiation with Auto MDI/MDI-X. At the default setting, the port, which is IEEE 802.3u compliant, sets its speed and duplex mode automatically with Auto- Negotiation. You can disable Auto-Negotiation and set the speed and duplex mode manually.

The wiring configuration of the port is set automatically with

Auto MDI/MDI-X to MDI or MDI-X, depending on the wiring configuration of the end node. This allows you to use a straight-through twisted-pair cable regardless of the wiring configuration of the port on the network device. The Auto MDI/MDI-X feature is only available when the port is using Auto-Negotiation. If the Auto-Negotiation feature is disabled with the Switchblade x3112 Management Software, the port defaults to the MDI-X setting.

NET MGMT LED

The Network Management (NET MGMT) port on the AT-SBx31CFC Fabric Control Card has one Status LED as displayed in Figure 8 and described in Table 5.

Console (RS-232) Port

Table 5. NET MGMT port LED Description

LED

State

Description

 

 

 

 

 

 

 

Solid Green

The port has a valid 1000 Mbps link.

 

 

 

 

Flashing

The port is transmitting or receiving data at

L/A

Green

1000 Mbps.

 

Solid Amber

The port has a valid 100 or 10 Mbps link.

 

 

 

 

Flashing

The port is transmitting or receiving data at

 

Amber

100 or 10 Mbps.

 

 

 

You use this port for local management with a console or a PC with a terminal emulation program. See Figure 8. This port does not require the AT-SBx31CFC Fabric Control Card to have an Internet Protocol (IP) address and is referred to as local or out-of-band management because it is not conducted over a network.

When initially configuring your SwitchBlade x3112 Switch, you first connect to this port with an RS-232 Serial Management cable. The cable is provided with the AT-SBx31CFC Fabric Control Card.

For instructions on how to start a local management session, refer to Chapter 2, “Starting a Local Management Session” on page 87 or refer to the Software Reference for SwitchBlade® x3100 Series Switches on the ATI web site. Go to “Where to Find Web-based Guides” on page 13 for information about how to navigate to this document.

26

Image 26
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterIntroduction Component Description ReferenceAT-SBx3112 Chassis Front View of the AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies AT-SBx31CFC Fabric Control Card SBx31CFCAT-SBx31CFC Fabric Control Card Features Status LEDs System Status LEDsLED State DescriptionSBx Status LEDs LEDs State DescriptionEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE AT-SBx31GP24 Power over Ethernet Power BudgetingAvailable at PoE PSU Maximum Range Maximum # Class UsagePorts with 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card AT-SBx31XZ4 LEDAT-SBx3161 System Power Supply AT-SBx3161 Status LEDsStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 PoE Power Supply AT-SBx3165 Status LEDsStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray AT-SBx31FAN Tray Power Power LED on the AT-SBx31FAN TrayOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location.  E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Preparing the Equipment Rack Reserving Vertical Rack SpaceUnpacking AT-SBx3112 Chassis Adjusting the Brackets Front Panel Position DimensionFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Installing the AT SBx3112 Chassis Equipment Rack Lifting AT-SBx3112 Chassis into PlaceRemoving the Front Panel Shipping Brace Screws Installing Chassis Ground Lug Attaching the Grounding Wire to the Grounding LugInstall the ground lug as displayed in Figure Protection Against Electrostatic Discharge ESD ESD SocketInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation Starting a Local Management Session SBx31CFCInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Weight Physical SpecificationsDimensions Appendix aEnvironmental Specifications Power SpecificationsSafety and Electromagnetic Emissions Certifications EMI/RFIConnectors and Port Pinouts Pin SignalPin Pair Signal Distance Cable RequirementsOperating