Allied Telesis AT-SBX31FAN, X3112, AT-SBX31GP24, AT-SBX31XZ4, AT-SBX3161 manual Officer SEC show card

Page 92

Chapter 3: Troubleshooting

SBx Status LEDs Flashing Amber on AT-SBx31CFC Fabric Control Card

If a SBx Status LED is flashing amber, the line card has experienced a FAULT or an error condition. See “SBx STATUS LED Description on the Active AT-SBx31CFC Fabric Control Card” on page 23 for an explanation of all status conditions.

Note

All line cards are hot swappable. This allows the AC power to be connected to the SwitchBlade x3112 while you re-seat or exchange line cards.

If a FAULT condition is encountered for one of the card slots, you can attempt to restart the line card. The following example is for restarting a card in slot 2:

officer SEC>> restart card 2

You will be prompted as follows - enter y for YES:

Do you really want to restart card 2 (Y/N)? y

Command has been submitted

officer SEC>>

If the RESTART CARD command is not successful, remove the line card from the slot and re-seat until the face plate is flush with the chassis front panel. Wait for 2 to 3 minutes for it to come on line. If it successfully comes up, the SBx Status LED for the slot in question turns to solid green.

You can obtain specific card status information for each card slot through the Switchblade x3112 Management Software by entering the SHOW CARD command as follows:

officer SEC>> show card

If the SBx Status LED for the slot is continues to flash amber after the above actions have been taken, contact Allied Telesis for further assistance. Please report the slot where the SBx Status LED fault condition is present and the information obtained from the SHOW CARD command.

92

Image 92

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterIntroduction Component Description ReferenceAT-SBx3112 Chassis Front View of the AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies AT-SBx31CFC Fabric Control Card SBx31CFCAT-SBx31CFC Fabric Control Card Features Status LEDs System Status LEDsLED State DescriptionSBx Status LEDs LEDs State DescriptionEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE AT-SBx31GP24 Power over Ethernet Power BudgetingMaximum Range Maximum # Class Usage Ports withAvailable at PoE PSU 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card AT-SBx31XZ4 LEDAT-SBx3161 System Power Supply AT-SBx3161 Status LEDsStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 PoE Power Supply AT-SBx3165 Status LEDsStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray AT-SBx31FAN Tray Power Power LED on the AT-SBx31FAN TrayOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location. E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Preparing the Equipment Rack Reserving Vertical Rack SpaceUnpacking AT-SBx3112 Chassis Adjusting the Brackets Front Panel Position DimensionFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Installing the AT SBx3112 Chassis Equipment Rack Lifting AT-SBx3112 Chassis into PlaceRemoving the Front Panel Shipping Brace Screws Installing Chassis Ground Lug Attaching the Grounding Wire to the Grounding LugInstall the ground lug as displayed in Figure Protection Against Electrostatic Discharge ESD ESD SocketInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation Starting a Local Management Session SBx31CFCInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Physical Specifications DimensionsWeight Appendix aEnvironmental Specifications Power SpecificationsSafety and Electromagnetic Emissions Certifications EMI/RFIConnectors and Port Pinouts Pin SignalPin Pair Signal Distance Cable RequirementsOperating