Allied Telesis AT-SBX31XZ4, X3112, AT-SBX31FAN, AT-SBX31GP24 manual Eco-friendly Button Reset Button

Page 24

Chapter 1: Overview

eco-friendly Button

RESET Button

The eco-friendly button on the AT-SBx31CFC Fabric Control Card front panel is used to turn off the LEDs on the line cards.This reduces the overall power consumption of the switch. It is displayed in Figure 7. You may want to turn off the LEDs when you are not using them to monitor the port status on the line card front panels.

With the LEDs are turned off, all of the LEDs in the chassis are affected except for the M/S LED on the active AT-SBx31CFC Fabric Control Card which is always illuminated.

The eco-friendly button is also used for a lamp test, which is initiated each time the button is pushed. The lamp test consists of LEDs flashing in alternating colors for 3 seconds.

RESET

Figure 7 eco-friendly Button and Reset Button

You can use the RESET button to reset the controller and switch fabric circuitry on the AT-SBx31CFC Fabric Control Card.This button is displayed in Figure 7. Push the button only in the unlikely event that the Switchblade x3112 Management Software is not responsive to CLI commands or status requests. Depending on your configuration, you may initiate a short interruption in the flow of network traffic through the switch when you press the button.

If you press the RESET button with only one AT-SBx31CFC Fabric Control Card installed, which is the active controller, all of the Ethernet line cards are reset by the AT-SBx31CFC Fabric Control Card as part of its boot up process.

Caution

When the RESET button is pressed with only one AT-SBx31CFC Fabric Control Card installed, the Ethernet network traffic flow through the switch is interrupted for up to two minutes while the AT- SBx31CFC and Ethernet line cards reboot.

If you press the RESET button with two AT-SBx31CFC Fabric Control Cards installed, the role of the active controller is “swapped” with the inactive controller. This means that the inactive controller becomes the

24

Image 24

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Power Specifications List of Figures Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card List of Tables List of Tables Preface Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterIntroduction Component Description ReferenceAT-SBx3112 Chassis Front View of the AT-SBx3112 ChassisAT-SBx3112 Chassis Slots Slot Line Cards/Power Supplies AT-SBx31CFC Fabric Control Card SBx31CFCAT-SBx31CFC Fabric Control Card Features Status LEDs System Status LEDsLED State DescriptionSBx Status LEDs LEDs State DescriptionEco-friendly Button Reset Button Network Management Port Console RS-232 Port USB Port SD Card Slot LEDs State Description AT-SBx31GP24 PoE Line Card Connector Type Speed Duplex Mode Maximum Distance Cable Type Auto MDI/ MDI-X Port Pinouts PoE AT-SBx31GP24 Power over Ethernet Power BudgetingMaximum Range Maximum # Class Usage Ports withAvailable at PoE PSU 1200 W 2400 WImplementation AT-SBx31XZ4 XFP Line Card AT-SBx31XZ4 LEDAT-SBx3161 System Power Supply AT-SBx3161 Status LEDsStatus LED Description on the AT-SBx3161 System Power Supply AT-SBx3165 PoE Power Supply AT-SBx3165 Status LEDsStatus LED Description on the AT-SBx3165 PoE Power Supply AT-SBx31FAN Tray AT-SBx31FAN Tray Power Power LED on the AT-SBx31FAN TrayOverview Installation Reviewing Safety Precautions SwitchBlade x3112 Installation Guide Access location. E45 Selecting a Site for the SwitchBlade Installing the AT-SBx3112 Chassis Preparing the Equipment Rack Reserving Vertical Rack SpaceUnpacking AT-SBx3112 Chassis Adjusting the Brackets Front Panel Position DimensionFactory Installed Flush with Rack Rails Rack Bracket Locations for Reverse Position of Chassis Installing the AT SBx3112 Chassis Equipment Rack Lifting AT-SBx3112 Chassis into PlaceRemoving the Front Panel Shipping Brace Screws Installing Chassis Ground Lug Attaching the Grounding Wire to the Grounding LugInstall the ground lug as displayed in Figure Protection Against Electrostatic Discharge ESD ESD SocketInstalling the AT-SBx3161 System Power Supply Unlocked Handle on the AT-SBx3161 System Power Supply Lock the Handle on the AT-SBx3161 System Power Supply Installation Installing the AT-SBx3165 PoE Power Supply Inserting the AT-SBx3165 PoE Power Supply 1887 Installing the AT-SBx31CFC Fabric Control Card Aligning the AT-SBx31CFC Card in the Chassis Slot 1825 1826 Installing the AT-SBx31GP24 PoE Line Card 1799 SBx31GP Installing the AT-SBx31XZ4 XFP Line Card Tightening Thumb Screws on the AT-SBx31XZ4 XFP Line Card SwitchBlade x3112 Installation Guide Installing an XFP Transceiver Replacing the AT-SBx31FAN Tray Inserting the AT-SBx31FAN Tray into the Chassis 1FAN Cabling the Twisted-Pair or Fiber Optic Ports Installing the Chassis Blank Panels Applying A/C Power to the SwitchBlade 1853 Installation Starting a Local Management Session SBx31CFCInstallation Troubleshooting Officer SEC Show PSU Officer SEC Show PSU Full Officer SEC Show Fanmodule Officer SEC show card Link LED is Off on AT-SBx31GP24 PoE Line Card Troubleshooting Port LED is Off on AT-SBx31XZ4 XFP Line Card Troubleshooting Cannot Establish a Local Out-of-Band Management Session Troubleshooting Physical Specifications DimensionsWeight Appendix aEnvironmental Specifications Power SpecificationsSafety and Electromagnetic Emissions Certifications EMI/RFIConnectors and Port Pinouts Pin SignalPin Pair Signal Cable Requirements OperatingDistance